Cisco Router and Switch Commands – GlobalBusinessArticles.biz

Use the commands in this chapter to configure various IP services. For configuration information and examples on IP services, refer to the “Configuring IP Services” chapter of the Network Protocols Configuration Guide, Part 1.

access-class

To restrict incoming and outgoing connections between a particular virtual terminal line (into a Cisco device) and the addresses in an access list, use the access-class line configuration command. To remove access restrictions, use the no form of this command.

access-class access-list-number {in | out}

no access-class access-list-number {in | out}

Syntax Description

access-list-number	Number of an IP access list. This is a decimal number from 1 to 199 or from 1300 to 2699.
in	Restricts incoming connections between a particular Cisco device and the addresses in the access list.
out	Restricts outgoing connections between a particular Cisco device and the addresses in the access list.

Defaults

No access lists are defined.

Command Modes

Line configuration

Command History

Release	Modification
10.0	This command was introduced.

Usage Guidelines

Remember to set identical restrictions on all the virtual terminal lines because a user can connect to any of them.

To display the access lists for a particular terminal line, use the show line EXEC command and specify the line number.

Examples

The following example defines an access list that permits only hosts on network 192.89.55.0 to connect to the virtual terminal ports on the router:

access-list 12 permit 192.89.55.0  0.0.0.255

 line 1 5

 access-class 12 in

The following example defines an access list that denies connections to networks other than network 36.0.0.0 on terminal lines 1 through 5:

access-list 10 permit 36.0.0.0 0.255.255.255

 line 1 5

 access-class 10 out

Related Commands

Command	Description
show line	Displays the parameters of a terminal line.

access-list (IP extended)

To define an extended IP access list, use the extended version of the access-list global configuration command. To remove the access lists, use the no form of this command.

access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit} protocol source source-wildcarddestination destination-wildcard [precedence precedence] [tos tos] [log | log-input] [fragments]

no access-list access-list-number

Internet Control Message Protocol (ICMP)

access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit} icmp source source-wildcarddestination destination-wildcard [icmp-type | [[icmp-type icmp-code] | [icmp-message]] [precedence precedence] [tos tos] [log |log-input] [fragments]

Internet Group Management Protocol (IGMP)

access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit} igmp source source-wildcard destination destination-wildcard [igmp-type] [precedence precedence] [tos tos] [log | log-input] [fragments]

TCP

access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit} tcp source source-wildcard [operator port [port]] destination destination-wildcard [operator port [port]] [established] [precedence precedence] [tos tos] [log | log-input] [fragments]

User Datagram Protocol (UDP)

access-list access-list-number [dynamic dynamic-name [timeout minutes]] {deny | permit}udp source source-wildcard [operator port [port]] destination destination-wildcard [operator port [port]] [precedence precedence] [tos tos] [log | log-input] [fragments]

Caution

Enhancements to this command are backward compatible; migrating from releases prior to Release 11.1 will convert your access lists automatically. However, releases prior to Release 11.1 are not upwardly compatible with these enhancements. Therefore, if you save an access list with these images and then use software prior to Release 11.1, the resulting access list will not be interpreted correctly. This could cause you severe security problems. Save your old configuration file before booting these images.

Syntax Description

access-list-number	Number of an access list. This is a decimal number from 100 to 199 or from 2000 to 2699.
dynamicdynamic-name	(Optional) Identifies this access list as a dynamic access list. Refer to lock-and-key access documented in the “Configuring Lock-and-Key Security (Dynamic Access Lists)” chapter in the Security Configuration Guide.
timeoutminutes	(Optional) Specifies the absolute length of time (in minutes) that a temporary access list entry can remain in a dynamic access list. The default is an infinite length of time and allows an entry to remain permanently. Refer to lock-and-key access documented in the “Configuring Lock-and-Key Security (Dynamic Access Lists)” chapter in the Security Configuration Guide.
deny	Denies access if the conditions are matched.
permit	Permits access if the conditions are matched.
protocol	Name or number of an IP protocol. It can be one of the keywords eigrp, gre, icmp,igmp, igrp, ip, ipinip, nos, ospf, pim, tcp, or udp, or an integer in the range 0 to 255 representing an IP protocol number. To match any Internet protocol (including ICMP, TCP, and UDP) use the keyword ip. Some protocols allow further qualifiers described below.
source	Number of the network or host from which the packet is being sent. There are three alternative ways to specify the source: •Use a 32-bit quantity in four-part, dotted-decimal format. •Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255. •Use host source as an abbreviation for a source and source-wildcard of source0.0.0.0.
source-wildcard	Wildcard bits to be applied to source. Each wildcard bit set to zero indicates that the corresponding bit position in the packet’s ip address must exactly match the bit value in the corresponding bit position in the source. Each wildcard bit set to one indicates that both a zero bit and a one bit in the corresponding position of the packet’s ip address will be considered a match to this access list entry. There are three alternative ways to specify the source wildcard: •Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. For example, 0.0.255.255 to require an exact match of only the first 16 bits of the source. •Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255. •Use host source as an abbreviation for a source and source-wildcard of source0.0.0.0. Wildcard bits set to one do not need to be contiguous in the source-wildcard. For example, a source-wildcard of 0.255.0.64 would be valid.
destination	Number of the network or host to which the packet is being sent. There are three alternative ways to specify the destination: •Use a 32-bit quantity in four-part, dotted-decimal format. •Use the keyword any as an abbreviation for the destination and destination-wildcardof 0.0.0.0 255.255.255.255. •Use host destination as an abbreviation for a destination and destination-wildcard ofdestination 0.0.0.0.
destination-wildcard	Wildcard bits to be applied to the destination. There are three alternative ways to specify the destination wildcard: •Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. •Use the keyword any as an abbreviation for a destination and destination-wildcard of 0.0.0.0 255.255.255.255. •Use host destination as an abbreviation for a destination and destination-wildcard ofdestination 0.0.0.0.
precedenceprecedence	(Optional) Packets can be filtered by precedence level, as specified by a number from 0 to 7 or by name as listed in the section “Usage Guidelines.”
tos tos	(Optional) Packets can be filtered by type of service level, as specified by a number from 0 to 15 or by name as listed in the section “Usage Guidelines.”
icmp-type	(Optional) ICMP packets can be filtered by ICMP message type. The type is a number from 0 to 255.
icmp-code	(Optional) ICMP packets that are filtered by ICMP message type can also be filtered by the ICMP message code. The code is a number from 0 to 255.
icmp-message	(Optional) ICMP packets can be filtered by an ICMP message type name or ICMP message type and code name. The possible names are found in the section “Usage Guidelines.”
igmp-type	(Optional) IGMP packets can be filtered by IGMP message type or message name. A message type is a number from 0 to 15. IGMP message names are listed in the section “Usage Guidelines.”
operator	(Optional) Compares source or destination ports. Possible operands include lt (less than),gt (greater than), eq (equal), neq (not equal), and range (inclusive range). If the operator is positioned after the source and source-wildcard, it must match the source port. If the operator is positioned after the destination and destination-wildcard, it must match the destination port. The range operator requires two port numbers. All other operators require one port number.
port	(Optional) The decimal number or name of a TCP or UDP port. A port number is a number from 0 to 65535. TCP port names are listed in the section “Usage Guidelines.” TCP port names can only be used when filtering TCP. UDP port names are listed in the section “Usage Guidelines.” UDP port names can only be used when filtering UDP. TCP port names can only be used when filtering TCP. UDP port names can only be used when filtering UDP.
established	(Optional) For the TCP protocol only: Indicates an established connection. A match occurs if the TCP datagram has the ACK, FIN, PSH, RST, SYN or URG control bits set. The nonmatching case is that of the initial TCP datagram to form a connection.
log	(Optional) Causes an informational logging message about the packet that matches the entry to be sent to the console. (The level of messages logged to the console is controlled by the logging console command.) The message includes the access list number, whether the packet was permitted or denied; the protocol, whether it was TCP, UDP, ICMP or a number; and, if appropriate, the source and destination addresses and source and destination port numbers. The message is generated for the first packet that matches, and then at 5-minute intervals, including the number of packets permitted or denied in the prior 5-minute interval. The logging facility might drop some logging message packets if there are too many to be handled or if there is more than one logging message to be handled in 1 second. This behavior prevents the router from crashing due to too many logging packets. Therefore, the logging facility should not be used as a billing tool or an accurate source of the number of matches to an access list.
log-input	(Optional) Includes the input interface and source MAC address or VC in the logging output.
fragments	(Optional) The access list entry applies to noninitial fragments of packets; the fragment is either permitted or denied accordingly. For more details about the fragments keyword, see the “Access List Processing of Fragments” and “Fragments and Policy Routing” sections in the “Usage Guidelines” section.

Defaults

An extended access list defaults to a list that denies everything. An extended access list is terminated by an implicit deny statement.

Command Modes

Global configuration

Command History

Release	Modification
10.0	This command and the UDP form of this command were introduced.
10.3	The ICMP, IGMP, and TCP forms of this command were introduced. The following keywords and arguments were added: •source •source-wildcard •destination •destination-wildcard •precedence precedence •icmp-type •icm-code •icmp-message •igmp-type •operator •port •established
11.1	The following keywords and arguments were added: •dynamic dynamic-name •timeout minutes
11.2	The following keyword was added: •log-input
12.0(11)	The fragments keyword was added.

Usage Guidelines

You can use access lists to control the transmission of packets on an interface, control virtual terminal line access, and restrict contents of routing updates. The Cisco IOS software stops checking the extended access list after a match occurs.

Note After an access list is created initially, any subsequent additions (possibly entered from the terminal) are placed at the end of the list. In other words, you cannot selectively add or remove access list command lines from a specific access list.

The following is a list of precedence names:

•critical •flash •flash-override •immediate •internet •network •priority •routine The following is a list of type of service (TOS) names: •max-reliability •max-throughput •min-delay •min-monetary-cost •normal The following is a list of ICMP message type names and ICMP message type and code names: •administratively-prohibited •alternate-address •conversion-error •dod-host-prohibited •dod-net-prohibited •echo •echo-reply •general-parameter-problem •host-isolated •host-precedence-unreachable •host-redirect •host-tos-redirect •host-tos-unreachable •host-unknown •host-unreachable •information-reply •information-request	•mask-reply •mask-request •mobile-redirect •net-redirect •net-tos-redirect •net-tos-unreachable •net-unreachable •network-unknown •no-room-for-option •option-missing •packet-too-big •parameter-problem •port-unreachable •precedence-unreachable •protocol-unreachable •reassembly-timeout •redirect •router-advertisement •router-solicitation •source-quench •source-route-failed •time-exceeded •timestamp-reply •timestamp-request •traceroute •ttl-exceeded •unreachable
The following is a list of IGMP message names:
•dvmrp •host-query •host-report •pim •trace
The following is a list of TCP port names that can be used instead of port numbers. Refer to the current Assigned Numbers RFC to find a reference to these protocols. Port numbers corresponding to these protocols can also be found by typing a ? in the place of a port number.
•bgp •chargen •daytime •discard •domain •echo •finger •ftp •ftp-data •gopher •hostname •irc •klogin •kshell •lpd	•nntp •pop2 •pop3 •smtp •sunrpc •syslog •tacacs-ds •talk •telnet •time •uucp •whois •www
The following is a list of UDP port names that can be used instead of port numbers. Refer to the current Assigned Numbers RFC to find a reference to these protocols. Port numbers corresponding to these protocols can also be found by typing a ? in the place of a port number.
•biff •bootpc •bootps •discard •dns •dnsix •echo •mobile-ip •nameserver •netbios-dgm •netbios-ns •ntp •rip	•snmp •snmptrap •sunrpc •syslog •tacacs-ds •talk •tftp •time •who •xdmcp

Access List Processing of Fragments

The behavior of access-list entries regarding the use or lack of the fragments keyword can be summarized as follows:

If the Access-List Entry has…

Then..

…no fragments keyword (the default behavior), and assuming all of the access-list entry information matches,

For an access-list entry containing only Layer 3 information:

•

The entry is applied to nonfragmented packets, initial fragments and noninitial fragments.

For an access list entry containing Layer 3 and Layer 4 information:

•

The entry is applied to nonfragmented packets and initial fragments.

–

If the entry is a permit statement, the packet or fragment is permitted.

–

If the entry is a deny statement, the packet or fragment is denied.

•

The entry is also applied to noninitial fragments in the following manner. Because noninitial fragments contain only Layer 3 information, only the Layer 3 portion of an access-list entry can be applied. If the Layer 3 portion of the access-list entry matches, and

–

If the entry is a permit statement, the noninitial fragment is permitted.

–

If the entry is a deny statement, the next access-list entry is processed.

Note

The deny statements are handled differently for noninitial fragments versus nonfragmented or initial fragments.

…the fragments keyword, and assuming all of the access-list entry information matches,

The access-list entry is applied only to noninitial fragments.

Note

The fragments keyword cannot be configured for an access-list entry that contains any Layer 4 information.

Be aware that you should not simply add the fragments keyword to every access list entry because the first fragment of the IP packet is considered a nonfragment and is treated independently of the subsequent fragments. An initial fragment will not match an access list permit or deny entry that contains the fragments keyword, the packet is compared to the next access list entry, and so on, until it is either permitted or denied by an access list entry that does not contain the fragments keyword. Therefore, you may need two access list entries for every deny entry. The first deny entry of the pair will not include the fragments keyword, and applies to the initial fragment. The second deny entry of the pair will include the fragments keyword and applies to the subsequent fragments. In the cases where there are multiple deny access list entries for the same host but with different Layer 4 ports, a singledeny access-list entry with the fragments keyword for that host is all that needs to be added. Thus all the fragments of a packet are handled in the same manner by the access list.

Packet fragments of IP datagrams are considered individual packets and each counts individually as a packet in access list accounting and access list violation counts.

Note The fragments keyword cannot solve all cases involving access lists and IP fragments.

Fragments and Policy Routing

Fragmentation and the fragment control feature affect policy routing if the policy routing is based on the match ip address command and the access list had entries that match on Layer 4 through 7 information. It is possible that noninitial fragments pass the access list and are policy routed, even if the first fragment was not policy routed or the reverse.

By using the fragments keyword in access list entries as described earlier, a better match between the action taken for initial and noninitial fragments can be made and it is more likely policy routing will occur as intended.

Examples

In the following example, serial interface 0 is part of a Class B network with the address 128.88.0.0, and the mail host’s address is 128.88.1.2. The keyword established is used only for the TCP protocol to indicate an established connection. A match occurs if the TCP datagram has the ACK or RST bits set, which indicate that the packet belongs to an existing connection.

access-list 102 permit tcp 0.0.0.0 255.255.255.255 128.88.0.0 0.0.255.255 established

access-list 102 permit tcp 0.0.0.0 255.255.255.255 128.88.1.2 0.0.0.0 eq 25

interface serial 0

 ip access-group 102 in

The following example also permit Domain Naming System (DNS) packets and ICMP echo and echo reply packets:

access-list 102 permit tcp any 128.88.0.0 0.0.255.255 established

access-list 102 permit tcp any host 128.88.1.2 eq smtp

access-list 102 permit tcp any any eq domain

access-list 102 permit udp any any eq domain

access-list 102 permit icmp any any echo

access-list 102 permit icmp any any echo-reply

The following examples show how wildcard bits are used to indicate the bits of the prefix or mask that are relevant. They are similar to the bitmasks that are used with normal access lists. Prefix/mask bits corresponding to wildcard bits set to 1 are ignored during comparisons and prefix/mask bits corresponding to wildcard bits set to 0 are used in comparison.

In the following example, permit 192.108.0.0 255.255.0.0 but deny any more specific routes of 192.108.0.0 (including 192.108.0.0 255.255.255.0).

access-list 101 permit ip 192.108.0.0 0.0.0.0   255.255.0.0 0.0.0.0 
access-list 101 deny ip 192.108.0.0 0.0.255.255  255.255.0.0 0.0.255.255

In the following example, permit 131.108.0/24 but deny 131.108/16 and all other subnets of 131.108.0.0.

access-list 101 permit ip 131.108.0.0 0.0.0.0     255.255.255.0 0.0.0.0 
access-list 101 deny ip 131.108.0.0 0.0.255.255 255.255.0.0   0.0.255.255

Related Commands


Command	Description
access-class	Restricts incoming and outgoing connections between a particular vty (into a Cisco device) and the addresses in an access list.
access-list (IP standard)	Defines a standard IP access list.
clear access-template	Clears a temporary access list entry from a dynamic access list manually.
distribute-list in (IP)	Filters networks received in updates.
distribute-list out (IP)	Suppresses networks from being advertised in updates.
ip access-group	Controls access to an interface.
ip access-list	Defines an IP access list by name.
ip accounting	Enables IP accounting on an interface.
logging console	Limits messages logged to the console based on severity.
show access-lists	Displays the contents of current IP and rate-limit access lists.
show ip access-list	Displays the contents of all current IP access lists.

access-list (IP standard)

To define a standard IP access list, use the standard version of the access-list global configuration command. To remove a standard access lists, use the no form of this command.

access-list access-list-number {deny | permit} source [source-wildcard] [log]

no access-list access-list-number

Caution

Enhancements to this command are backward compatible; migrating from releases prior to Release 10.3 will convert your access lists automatically. However, releases prior to Release 10.3 are not upwardly compatible with these enhancements. Therefore, if you save an access list with these images and then use software prior to Release 10.3, the resulting access list will not be interpreted correctly. This could cause you severe security problems. Save your old configuration file before booting these images.

Syntax Description


access-list-number	Number of an access list. This is a decimal number from1 to 99 or from 1300 to 1999.
deny	Denies access if the conditions are matched.
permit	Permits access if the conditions are matched.
source	Number of the network or host from which the packet is being sent. There are two alternative ways to specify the source: Use a 32-bit quantity in four-part, dotted-decimal format. Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255.
source-wildcard	(Optional) Wildcard bits to be applied to source. Each wildcard bit set to zero indicates that the corresponding bit position in the packet’s ip address must exactly match the bit value in the corresponding bit position in the source. Each wildcard bit set to one indicates that both a zero bit and a one bit in the corresponding position of the packet’s ip address will be considered a match to this access list entry. There are two alternative ways to specify the source wildcard: Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. For example, 0.0.255.255 to require an exact match of only the first 16 bits of the source. Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255. Wildcard bits set to one do not need to be contiguous in the source-wildcard. For example, asource-wildcard of 0.255.0.64 would be valid.
log	(Optional) Causes an informational logging message about the packet that matches the entry to be sent to the console. (The level of messages logged to the console is controlled by thelogging console command.) The message includes the access list number, whether the packet was permitted or denied, the source address, and the number of packets. The message is generated for the first packet that matches, and then at 5-minute intervals, including the number of packets permitted or denied in the prior 5-minute interval. The logging facility might drop some logging message packets if there are too many to be handled or if there is more than one logging message to be handled in 1 second. This behavior prevents the router from crashing due to too many logging packets. Therefore, the logging facility should not be used as a billing tool or an accurate source of the number of matches to an access list.

Defaults

The access list defaults to an implicit deny statement for everything. The access list is always terminated by an implicit deny statement for everything.

Command Modes

Global configuration

Command History


Release	Modification
10.3	This command was introduced.
11.3(3)T	The log keyword was added.

Usage Guidelines

Plan your access conditions carefully and be aware of the implicit deny statement at the end of the access list.

You can use access lists to control the transmission of packets on an interface, control virtual terminal line access, and restrict the contents of routing updates.

Use the show access-lists EXEC command to display the contents of all access lists.

Use the show ip access-list EXEC command to display the contents of one access list.

Examples

The following example of a standard access list allows access for only those hosts on the three specified networks. The wildcard bits apply to the host portions of the network addresses. Any host with a source address that does not match the access list statements will be rejected.

access-list 1 permit 192.5.34.0  0.0.0.255

access-list 1 permit 128.88.0.0  0.0.255.255

access-list 1 permit 36.0.0.0  0.255.255.255

! (Note: all other access implicitly denied)

The following example of a standard access list allows access for devices with IP addresses in the range 10.29.2.64 to 10.29.2.127. All packets with a source address not in this range will be rejected.

access-list 1 permit 10.29.2.64 0.0.0.63

! (Note: all other access implicitly denied)

To specify a large number of individual addresses more easily, you can omit the wildcard if it is all zeros. Thus, the following two configuration commands are identical in effect:

access-list 2 permit 36.48.0.3

access-list 2 permit 36.48.0.3  0.0.0.0

Related Commands


Command	Description
access-class	Restricts incoming and outgoing connections between a particular vty (into a Cisco device) and the addresses in an access list.
access-list (IP extended)	Defines an extended IP access list.
distribute-list in (IP)	Filters networks received in updates.
distribute-list out (IP)	Suppresses networks from being advertised in updates.
ip access-group	Controls access to an interface.
show access-lists	Displays the contents of current IP and rate-limit access lists.
show ip access-list	Displays the contents of all current IP access lists.

clear access-list counters

To clear the counters of an access list, use the clear access-list counters EXEC command.

clear access-list counters {access-list-number | name}

Syntax Description


access-list-number	Access list number of the access list for which to clear the counters.
name	Name of an IP access list. The name cannot contain a space or quotation mark, and must begin with an alphabetic character to avoid ambiguity with numbered access lists.

Command Modes

EXEC

Command History


Release	Modification
11.0	This command was introduced.

Usage Guidelines

Some access lists keep counters that count the number of packets that pass each line of an access list. The show access-listscommand displays the counters as a number of matches. Use the clear access-list counters command to restart the counters for a particular access list to 0.

Examples

The following example clears the counters for access list 101:

clear access-list counters 101

Related Commands


Command	Description
show access-lists	Displays the contents of current IP and rate-limit access lists.

clear ip accounting

To clear the active or checkpointed database when IP accounting is enabled, use the clear ip accounting EXEC command.

clear ip accounting [checkpoint]

Syntax Description


checkpoint	(Optional) Clears the checkpointed database.

Command Modes

EXEC

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

You can also clear the checkpointed database by issuing the clear ip accounting command twice in succession.

Examples

The following example clears the active database when IP accounting is enabled:

clear ip accounting

Related Commands

Command	Description
ip accounting	Enables IP accounting on an interface.
ip accounting-list	Defines filters to control the hosts for which IP accounting information is kept.
ip accounting-threshold	Sets the maximum number of accounting entries to be created.
ip accounting-transits	Controls the number of transit records that are stored in the IP accounting database.
show ip accounting	Displays the active accounting or checkpointed database or displays access list violations.

clear ip drp

To clear all statistics being collected on Director Response Protocol (DRP) requests and replies, use the clear ip drp EXEC command.

clear ip drp

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History


Release	Modification
11.2 F	This command was introduced.

Examples

The following example clears all DRP statistics:

clear ip drp

Related Commands

Command	Description
ip drp access-group	Controls the sources of DRP queries to the DRP Server Agent.
ip drp authentication key-chain	Configures authentication on the DRP Server Agent for DistributedDirector.

clear tcp statistics

To clear TCP statistics, use the clear tcp statistics EXEC command.

clear tcp statistics

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC

Command History


Release	Modification
11.3	This command was introduced.

Examples

The following example clears all TCP statistics:

clear tcp statistics

Related Commands

Command	Description
show tcp statistics	Displays TCP statistics.

deny (IP)

To set conditions for a named IP access list, use the deny access-list configuration command. To remove a deny condition from an access list, use the no form of this command.

deny {source [source-wildcard] | any} [log]

no deny {source [source-wildcard] | any}

deny protocol source source-wildcard destination destination-wildcard [precedence precedence] [tos tos] [log] [fragments]

no deny protocol source source-wildcard destination destination-wildcard

ICMP

deny icmp source source-wildcard destination destination-wildcard [icmp-type [icmp-code] | icmp-message] [precedenceprecedence] [tos tos] [log] [fragments]

IGMP

deny igmp source source-wildcard destination destination-wildcard [igmp-type] [precedence precedence] [tos tos] [log] [fragments]

TCP

deny tcp source source-wildcard [operator port [port]] destination destination-wildcard [operator port [port]] [established] [precedence precedence] [tos tos] [log] [fragments]

UDP

deny udp source source-wildcard [operator port [port]] destination destination-wildcard [operator port [port]] [precedenceprecedence] [tos tos] [log] [fragments]

Syntax Description

source	Number of the network or host from which the packet is being sent. There are two alternative ways to specify the source: Use a 32-bit quantity in four-part, dotted-decimal format. Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255.
source-wildcard	(Optional) Wildcard bits to be applied to the source. There are two alternative ways to specify the source wildcard: Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255.
protocol	Name or number of an IP protocol. It can be one of the keywords eigrp, gre, icmp,igmp, igrp, ip, ipinip, nos, ospf, tcp, or udp, or an integer in the range 0 to 255 representing an IP protocol number. To match any Internet protocol (including ICMP, TCP, and UDP), use the keyword ip. Some protocols allow further qualifiers described later.
source	Number of the network or host from which the packet is being sent. There are three alternative ways to specify the source: •Use a 32-bit quantity in four-part, dotted-decimal format. •Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255. •Use host source as an abbreviation for a source and source-wildcard of source0.0.0.0.
source-wildcard	Wildcard bits to be applied to source. There are three alternative ways to specify the source wildcard: •Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. •Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255. •Use host source as an abbreviation for a source and source-wildcard of source0.0.0.0.
destination	Number of the network or host to which the packet is being sent. There are three alternative ways to specify the destination: •Use a 32-bit quantity in four-part, dotted-decimal format. •Use the keyword any as an abbreviation for the destination and destination-wildcardof 0.0.0.0 255.255.255.255. •Use host destination as an abbreviation for a destination and destination-wildcard ofdestination 0.0.0.0.
destination-wildcard	Wildcard bits to be applied to the destination. There are three alternative ways to specify the destination wildcard: •Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. •Use the keyword any as an abbreviation for a destination and destination-wildcard of0.0.0.0 255.255.255.255. •Use host destination as an abbreviation for a destination and destination-wildcard ofdestination 0.0.0.0.
precedenceprecedence	(Optional) Packets can be filtered by precedence level, as specified by a number from 0 to 7 or by name as listed in the section “Usage Guidelines.”
tos tos	(Optional) Packets can be filtered by type of service level, as specified by a number from 0 to 15 or by name as listed in the “Usage Guidelines” section of the access-list (IP extended) command.
icmp-type	(Optional) ICMP packets can be filtered by ICMP message type. The type is a number from 0 to 255.
icmp-code	(Optional) ICMP packets which are filtered by ICMP message type can also be filtered by the ICMP message code. The code is a number from 0 to 255.
icmp-message	(Optional) ICMP packets can be filtered by an ICMP message type name or ICMP message type and code name. The possible names are found in the “Usage Guidelines” section of the access-list (IP extended) command.
igmp-type	(Optional) IGMP packets can be filtered by IGMP message type or message name. A message type is a number from 0 to 15. IGMP message names are listed in the “Usage Guidelines” section of the access-list (IP extended) command.
operator	(Optional) Compares source or destination ports. Possible operands include lt (less than),gt (greater than), eq (equal), neq (not equal), and range (inclusive range). If the operator is positioned after the source and source-wildcard, it must match the source port. If the operator is positioned after the destination and destination-wildcard, it must match the destination port. The range operator requires two port numbers. All other operators require one port number.
port	(Optional) The decimal number or name of a TCP or UDP port. A port number is a number from 0 to 65535. TCP and UDP port names are listed in the “Usage Guidelines” section of the access-list (IP extended) command. TCP port names can only be used when filtering TCP. UDP port names can only be used when filtering UDP.
established	(Optional) For the TCP protocol only: Indicates an established connection. A match occurs if the TCP datagram has the ACK or RST bits set. The nonmatching case is that of the initial TCP datagram to form a connection.
log	(Optional) Causes an informational logging message about the packet that matches the entry to be sent to the console. (The level of messages logged to the console is controlled by the logging console command.) The message for a standard list includes the access list number, whether the packet was permitted or denied, the source address, and the number of packets. The message for an extended list includes the access list number; whether the packet was permitted or denied; the protocol; whether it was TCP, UDP, ICMP, or a number; and, if appropriate, the source and destination addresses and source and destination port numbers. For both standard and extended lists, the message is generated for the first packet that matches, and then at 5-minute intervals, including the number of packets permitted or denied in the prior 5-minute interval. The logging facility might drop some logging message packets if there are too many to be handled or if there is more than one logging message to be handled in 1 second. This behavior prevents the router from crashing due to too many logging packets. Therefore, the logging facility should not be used as a billing tool or an accurate source of the number of matches to an access list.
fragments	(Optional) The access list entry applies to noninitial fragments of packets; the fragment is either permitted or denied accordingly. For more details about the fragments keyword, see the “Access List Processing of Fragments” and “Fragments and Policy Routing” sections in the “Usage Guidelines” section.

Defaults

There is no specific condition under which a packet is denied passing the named access list.

Command Modes

Access-list configuration

Command History


Release	Modification
11.2	This command was introduced.
11.3(3)T	The log keyword for a standard access was added.
12.0(11)	The fragments keyword was added.

Usage Guidelines

Use this command following the ip access-list command to specify conditions under which a packet cannot pass the named access list.

Access List Processing of Fragments

The behavior of access-list entries regarding the use or lack of the fragments keyword can be summarized as follows:

If the Access-List Entry has…

Then..

…no fragments keyword (the default behavior), and assuming all of the access-list entry information matches,

For an access-list entry containing only Layer 3 information:

•

The entry is applied to nonfragmented packets, initial fragments and noninitial fragments.

For an access list entry containing Layer 3 and Layer 4 information:

•

The entry is applied to nonfragmented packets and initial fragments.

–

If the entry is a permit statement, the packet or fragment is permitted.

–

If the entry is a deny statement, the packet or fragment is denied.

•

–

If the entry is a permit statement, the noninitial fragment is permitted.

–

If the entry is a deny statement, the next access-list entry is processed.

Note

The deny statements are handled differently for noninitial fragments versus nonfragmented or initial fragments.

…the fragments keyword, and assuming all of the access-list entry information matches,

Note

The access-list entry is applied only to noninitial fragments.Thefragments keyword cannot be configured for an access-list entry that contains any Layer 4 information.

Packet fragments of IP datagrams are considered individual packets and each counts individually as a packet in access list accounting and access list violation counts.

Note The fragments keyword cannot solve all cases involving access lists and IP fragments.

Fragments and Policy Routing

Examples

The following example sets a deny condition for a standard access list named Internetfilter:

ip access-list standard Internetfilter

 deny 192.5.34.0  0.0.0.255

 permit 128.88.0.0  0.0.255.255

 permit 36.0.0.0  0.255.255.255

! (Note: all other access implicitly denied)

Related Commands


Command	Description
ip access-group	Controls access to an interface.
ip access-list	Defines an IP access list by name.
logging console	Limits messages logged to the console based on severity.
permit (IP)	Sets conditions for a named IP access list.
show access-lists	Displays the contents of all current IP access lists.

dynamic

To define a named, dynamic, IP access list, use the dynamic access-list configuration command. To remove the access lists, use the no form of this command.

dynamic dynamic-name [timeout minutes] {deny | permit} protocol source source-wildcard destination destination-wildcard[precedence precedence] [tos tos] [log] [fragments]

no dynamic dynamic-name

ICMP

dynamic dynamic-name [timeout minutes] {deny | permit} icmp source source-wildcard destination destination-wildcard [icmp-type [icmp-code] | icmp-message] [precedence precedence] [tos tos] [log] [fragments]

IGMP

dynamic dynamic-name [timeout minutes] {deny | permit} igmp source source-wildcard destination destination-wildcard [igmp-type] [precedence precedence] [tos tos] [log] [fragments]

TCP

dynamic dynamic-name [timeout minutes] {deny | permit} tcp source source-wildcard [operator port [port]] destination destination-wildcard [operator port [port]] [established] [precedence precedence] [tos tos] [log] [fragments]

UDP

dynamic dynamic-name [timeout minutes] {deny | permit} udp source source-wildcard [operator port [port]] destinationdestination-wildcard [operator port [port]] [precedence precedence] [tos tos] [log] [fragments]

Caution

Named IP access lists will not be recognized by any software release prior to Cisco IOS Release 11.2.

Syntax Description


dynamic-name	Identifies this access list as a dynamic access list. Refer to lock-and-key access documented in the “Configuring Lock-and-Key Security (Dynamic Access Lists)” chapter in the Security Configuration Guide.
timeoutminutes	(Optional) Specifies the absolute length of time (in minutes) that a temporary access list entry can remain in a dynamic access list. The default is an infinite length of time and allows an entry to remain permanently. Refer to lock-and-key access documented in the “Configuring Lock-and-Key Security (Dynamic Access Lists)” chapter in the Security Configuration Guide.
deny	Denies access if the conditions are matched.
permit	Permits access if the conditions are matched.
protocol	Name or number of an IP protocol. It can be one of the keywords eigrp, gre, icmp,igmp, igrp, ip, ipinip, nos, ospf, tcp, or udp, or an integer in the range 0 to 255 representing an IP protocol number. To match any Internet protocol (including ICMP, TCP, and UDP), use the keyword ip. Some protocols allow further qualifiers described later.
source	Number of the network or host from which the packet is being sent. There are three alternative ways to specify the source: Use a 32-bit quantity in four-part, dotted-decimal format. •Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255. •Use host source as an abbreviation for a source and source-wildcard of source0.0.0.0.
source-wildcard	Wildcard bits to be applied to source. There are three alternative ways to specify the source wildcard: •Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. •Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255. •Use host source as an abbreviation for a source and source-wildcard of source0.0.0.0.
destination	Number of the network or host to which the packet is being sent. There are three alternative ways to specify the destination: •Use a 32-bit quantity in four-part, dotted-decimal format. •Use the keyword any as an abbreviation for the destination and destination-wildcardof 0.0.0.0 255.255.255.255. •Use host destination as an abbreviation for a destination and destination-wildcard ofdestination 0.0.0.0.
destination-wildcard	Wildcard bits to be applied to the destination. There are three alternative ways to specify the destination wildcard: •Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. •Use the keyword any as an abbreviation for a destination and destination-wildcard of0.0.0.0 255.255.255.255. •Use host destination as an abbreviation for a destination and destination-wildcard ofdestination 0.0.0.0.
precedenceprecedence	(Optional) Packets can be filtered by precedence level, as specified by a number from 0 to 7 or by name as listed in the section “Usage Guidelines.”
tos tos	(Optional) Packets can be filtered by type of service level, as specified by a number from 0 to 15 or by name as listed in the section “Usage Guidelines.”
icmp-type	(Optional) ICMP packets can be filtered by ICMP message type. The type is a number from 0 to 255.
icmp-code	(Optional) ICMP packets which are filtered by ICMP message type can also be filtered by the ICMP message code. The code is a number from 0 to 255.
icmp-message	(Optional) ICMP packets can be filtered by an ICMP message type name or ICMP message type and code name. The possible names are found in the section “Usage Guidelines.”
igmp-type	(Optional) IGMP packets can be filtered by IGMP message type or message name. A message type is a number from 0 to 15. IGMP message names are listed in the section “Usage Guidelines.”
operator	(Optional) Compares source or destination ports. Possible operands include lt (less than),gt (greater than), eq (equal), neq (not equal), and range (inclusive range). If the operator is positioned after the source and source-wildcard, it must match the source port. If the operator is positioned after the destination and destination-wildcard, it must match the destination port. The range operator requires two port numbers. All other operators require one port number.
port	(Optional) The decimal number or name of a TCP or UDP port. A port number is a number from 0 to 65535. TCP and UDP port names are listed in the “Usage Guidelines” section of the access-list (IP extended) command. TCP port names can only be used when filtering TCP. UDP port names can only be used when filtering UDP.
established	(Optional) For the TCP protocol only: Indicates an established connection. A match occurs if the TCP datagram has the ACK or RST bits set. The nonmatching case is that of the initial TCP datagram to form a connection.
log	(Optional) Causes an informational logging message about the packet that matches the entry to be sent to the console. (The level of messages logged to the console is controlled by the logging console command.) The message includes the access list number, whether the packet was permitted or denied; the protocol, whether it was TCP, UDP, ICMP or a number; and, if appropriate, the source and destination addresses and source and destination port numbers. The message is generated for the first packet that matches, and then at 5-minute intervals, including the number of packets permitted or denied in the prior 5-minute interval. The logging facility might drop some logging message packets if there are too many to be handled or if there is more than one logging message to be handled in 1 second. This behavior prevents the router from crashing due to too many logging packets. Therefore, the logging facility should not be used as a billing tool or an accurate source of the number of matches to an access list.
fragments	(Optional) The access list entry applies to noninitial fragments of packets; the fragment is either permitted or denied accordingly. For more details about the fragments keyword, see the “Access List Processing of Fragments” and “Fragments and Policy Routing” sections in the “Usage Guidelines” section.

Defaults

An extended access list defaults to a list that denies everything. An extended access list is terminated by an implicit deny statement.

Command Modes

Access-list configuration

Command History


Release	Modification
11.2	This command was introduced.
12.0(11)	The fragments keyword was added.

Usage Guidelines

You can use named access lists to control the transmission of packets on an interface and restrict contents of routing updates. The Cisco IOS software stops checking the extended access list after a match occurs.

Fragmented IP packets, other than the initial fragment, are immediately accepted by any extended IP access list. Extended access lists used to control virtual terminal line access or restrict contents of routing updates must not match against the TCP source port, the type of service value, or the packet’s precedence.

The following is a list of precedence names:

•

critical

•

flash

•

flash-override

•

immediate

•

internet

•

network

•

priority

•

routine

The following is a list of type of service (TOS) names:

•

max-reliability

•

max-throughput

•

min-delay

•

min-monetary-cost

•

normal

The following is a list of ICMP message type names and ICMP message type and code names:

•

administratively-prohibited

•

alternate-address

•

conversion-error

•

dod-host-prohibited

•

dod-net-prohibited

•

echo

•

echo-reply

•

general-parameter-problem

•

host-isolated

•

host-precedence-unreachable

•

host-redirect

•

host-tos-redirect

•

host-tos-unreachable

•

host-unknown

•

host-unreachable

•

information-reply

•

information-request

•

mask-reply

•

mask-request

•

mobile-redirect

•

net-redirect

•

net-tos-redirect

•

net-tos-unreachable

•

net-unreachable

•

network-unknown

•

no-room-for-option

•

option-missing

•

packet-too-big

•

parameter-problem

•

port-unreachable

•

precedence-unreachable

•

protocol-unreachable

•

reassembly-timeout

•

redirect

•

router-advertisement

•

router-solicitation

•

source-quench

•

source-route-failed

•

time-exceeded

•

timestamp-reply

•

timestamp-request

•

traceroute

•

ttl-exceeded

•

unreachable

The following is a list of IGMP message names:

•

dvmrp

•

host-query

•

host-report

•

pim

•

trace

The following is a list of TCP port names that can be used instead of port numbers. Refer to the current Assigned Numbers RFC to find a reference to these protocols. Port numbers corresponding to these protocols can also be found by typing a ? in the place of a port number.

•

bgp

•

chargen

•

daytime

•

discard

•

domain

•

echo

•

finger

•

ftp

•

ftp-data

•

gopher

•

hostname

•

irc

•

klogin

•

kshell

•

lpd

•

nntp

•

pop2

•

pop3

•

smtp

•

sunrpc

•

syslog

•

tacacs-ds

•

talk

•

telnet

•

time

•

uucp

•

whois

•

www

The following is a list of UDP port names that can be used instead of port numbers. Refer to the current Assigned Numbers RFC to find a reference to these protocols. Port numbers corresponding to these protocols can also be found by typing a ? in the place of a port number.

•

biff

•

bootpc

•

bootps

•

discard

•

dns

•

dnsix

•

echo

•

mobile-ip

•

nameserver

•

netbios-dgm

•

netbios-ns

•

ntp

•

rip

•

snmp

•

snmptrap

•

sunrpc

•

syslog

•

tacacs-ds

•

talk

•

tftp

•

time

•

who

•

xdmcp

Access List Processing of Fragments

The behavior of access-list entries regarding the use or lack of the fragments keyword can be summarized as follows:


If the Access-List Entry has…	Then..
…no fragments keyword (the default behavior), and assuming all of the access-list entry information matches,	For an access-list entry containing only Layer 3 information: •The entry is applied to nonfragmented packets, initial fragments and noninitial fragments. For an access list entry containing Layer 3 and Layer 4 information: •The entry is applied to nonfragmented packets and initial fragments. –If the entry is a permit statement, the packet or fragment is permitted. –If the entry is a deny statement, the packet or fragment is denied. •The entry is also applied to noninitial fragments in the following manner. Because noninitial fragments contain only Layer 3 information, only the Layer 3 portion of an access-list entry can be applied. If the Layer 3 portion of the access-list entry matches, and –If the entry is a permit statement, the noninitial fragment is permitted. –If the entry is a deny statement, the next access-list entry is processed. Note The deny statements are handled differently for noninitial fragments versus nonfragmented or initial fragments.
…the fragments keyword, and assuming all of the access-list entry information matches,	Note The access-list entry is applied only to noninitial fragments.Thefragments keyword cannot be configured for an access-list entry that contains any Layer 4 information.

Packet fragments of IP datagrams are considered individual packets and each counts individually as a packet in access list accounting and access list violation counts.

Note The fragments keyword cannot solve all cases involving access lists and IP fragments.

Fragments and Policy Routing

Examples

The following example defines a dynamic access list named washington:

ip access-group washington in

ip access-list extended washington

 dynamic testlist timeout 5

 permit ip any any

 permit tcp any host 185.302.21.2 eq 23

Related Commands


Command	Description
clear access-template	Clears a temporary access list entry from a dynamic access list manually.
distribute-list in (IP)	Filters networks received in updates.
distribute-list out (IP)	Suppresses networks from being advertised in updates.
ip access-group	Controls access to an interface.
ip access-list	Defines an IP access list by name.
logging console	Limits messages logged to the console based on severity.
show access-lists	Displays the contents of current IP and rate-limit access lists.
show ip access-list	Displays the contents of all current IP access lists.

ip access-group

To control access to an interface, use the ip access-group interface configuration command. To remove the specified access group, use the no form of this command.

ip access-group {access-list-number | name}{in | out}

no ip access-group {access-list-number | name}{in | out}

Syntax Description


access-list-number	Number of an access list. This is a decimal number from 1 to 199 or from 1300 to 2699.
name	Name of an IP access list as specified by an ip access-list command.
in	Filters on inbound packets.
out	Filters on outbound packets.

Defaults

No access list is applied to the interface.

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.
11.2	The name argument was added.

Usage Guidelines

Access lists are applied on either outbound or inbound interfaces. For standard inbound access lists, after receiving a packet, the Cisco IOS software checks the source address of the packet against the access list. For extended access lists, the router also checks the destination access list. If the access list permits the address, the software continues to process the packet. If the access list rejects the address, the software discards the packet and returns an ICMP Host Unreachable message.

For standard outbound access lists, after receiving and routing a packet to a controlled interface, the software checks the source address of the packet against the access list. For extended access lists, the router also checks the destination access list. If the access list permits the address, the software transmits the packet. If the access list rejects the address, the software discards the packet and returns an ICMP Host Unreachable message.

If the specified access list does not exist, all packets are passed.

When you enable outbound access lists, you automatically disable autonomous switching for that interface.When you enable input access lists on any cBus or CxBus interface, you automatically disable autonomous switching for all interfaces (with one exception—an SSE configured with simple access lists can still switch packets, on output only).

Examples

The following example applies list 101 on packets outbound from Ethernet interface 0:

interface ethernet 0

 ip access-group 101 out

Related Commands


Command	Description
access-list (IP extended)	Defines an extended IP access list.
access-list (IP standard)	Defines a standard IP access list.
ip access-list	Defines an IP access list by name.
show access-lists	Displays the contents of current IP and rate-limit access lists.

ip access-list

To define an IP access list by name, use the ip access-list global configuration command. To remove a named IP access lists, use the no form of this command.

ip access-list {standard | extended} name

no ip access-list {standard | extended} name

Caution

Named access lists will not be recognized by any software release prior to Cisco IOS Release 11.2.

Syntax Description


standard	Specifies a standard IP access list.
extended	Specifies an extended IP access list.
name	Name of the access list. Names cannot contain a space or quotation mark, and must begin with an alphabetic character to prevent ambiguity with numbered access lists.

Defaults

No named IP access list is defined.

Command Modes

Global configuration

Command History


Release	Modification
11.2	This command was introduced.

Usage Guidelines

Use this command to configure a named IP access list as opposed to a numbered IP access list. This command will take you into access-list configuration mode, where you must define the denied or permitted access conditions with the deny and permitcommands.

Specifying standard or extended with the ip access-list command determines the prompt you get when you enter access-list configuration mode.

Use the ip access-group command to apply the access-list to an interface.

Named access lists are not compatible with Cisco IOS releases prior to Release 11.2.

Examples

The following example defines a standard access list named Internetfilter:

ip access-list standard Internetfilter

 permit 192.5.34.0  0.0.0.255

 permit 128.88.0.0  0.0.255.255

 permit 36.0.0.0  0.255.255.255

! (Note: all other access implicitly denied)

Related Commands


Command	Description
deny (IP)	Sets conditions for a named IP access list.
ip access-group	Controls access to an interface.
permit (IP)	Sets conditions for a named IP access list.
show access-lists	Displays the contents of all current IP access lists.

ip accounting

To enable IP accounting on an interface, use the ip accounting interface configuration command. To disable IP accounting, use theno form of this command.

ip accounting [access-violations] [output-packets]

no ip accounting [access-violations] [output-packets]

Syntax Description


access-violations	(Optional) Enables IP accounting with the ability to identify IP traffic that fails IP access lists.
output-packets	(Optional) Enables IP accounting based on the IP packets output on the interface.

Defaults

Disabled

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.
10.3	The access-violations keyword was added.

Usage Guidelines

The ip accounting command records the number of bytes (IP header and data) and packets switched through the system on a source and destination IP address basis. Only transit IP traffic is measured and only on an outbound basis; traffic generated by the router access server or terminating in this device is not included in the accounting statistics. Use the show ip accounting command to display the active accounting database, and traffic coming from a remote site and transiting through a router.

If you specify the access-violations keyword, ip accounting provides information identifying IP traffic that fails IP access lists. Identifying IP source addresses that violate IP access lists alerts you to possible attempts to breach security. The data might also indicate that you should verify IP access list configurations.

To receive a logging message on the console when an extended access list entry denies a packet access (to log violations), you must include the log keyword in the access-list (IP extended) or access-list (IP standard) command.

Statistics are accurate even if IP fast switching or IP access lists are being used on the interface.

IP accounting disables autonomous switching, SSE switching, and distributed switching (dCEF) on the interface. IP accounting will cause packets to be switched on the Route Switch Processor (RSP) instead of the Versatile Interface Processor (VIP), which can cause performance degradation.

Examples

The following example enables IP accounting on Ethernet interface 0:

interface ethernet 0

 ip accounting

Related Commands


Command	Description
access-list (IP extended)	Defines an extended IP access list.
access-list (IP standard)	Defines a standard IP access list.
clear ip accounting	Clears the active or checkpointed database when IP accounting is enabled.
ip accounting-list	Defines filters to control the hosts for which IP accounting information is kept.
ip accounting-threshold	Sets the maximum number of accounting entries to be created.
ip accounting-transits	Controls the number of transit records that are stored in the IP accounting database.
show ip accounting	Displays the active accounting or checkpointed database or displays access list violations.

ip accounting-list

To define filters to control the hosts for which IP accounting information is kept, use the ip accounting-list global configuration command. To remove a filter definition, use the no form of this command.

ip accounting-list ip-address wildcard

no ip accounting-list ip-address wildcard

Syntax Description


ip-address	IP address in dotted-decimal format.
wildcard	Wildcard bits to be applied to ip-address.

Defaults

No filters are defined.

Command Modes

Global configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

The source and destination address of each IP datagram is logically ANDed with the wildcard bits and compared with the ip-address. If there is a match, the information about the IP datagram will be entered into the accounting database. If there is no match, the IP datagram is considered a transit datagram and will be counted according to the setting of the ip accounting-transits global configuration command.

Examples

The following example adds all hosts with IP addresses beginning with 192.31 to the list of hosts for which accounting information will be kept:

ip accounting-list 192.31.0.0 0.0.255.255

Related Commands


Command	Description
clear ip accounting	Clears the active or checkpointed database when IP accounting is enabled.
ip accounting	Enables IP accounting on an interface.
ip accounting-threshold	Sets the maximum number of accounting entries to be created.
ip accounting-transits	Controls the number of transit records that are stored in the IP accounting database.
show ip accounting	Displays the active accounting or checkpointed database or displays access list violations.

ip accounting-threshold

To set the maximum number of accounting entries to be created, use the ip accounting-threshold global configuration command. To restore the default number of entries, use the no form of this command.

ip accounting-threshold threshold

no ip accounting-threshold threshold

Syntax Description


threshold	Maximum number of entries (source and destination address pairs) that the Cisco IOS software accumulates.

Defaults

512 entries

Command Modes

Global configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

The accounting threshold defines the maximum number of entries (source and destination address pairs) that the software accumulates, preventing IP accounting from possibly consuming all available free memory. This level of memory consumption could occur in a router that is switching traffic for many hosts. Overflows will be recorded; see the monitoring commands for display formats.

The default accounting threshold of 512 entries results in a maximum table size of 12,928 bytes. Active and checkpointed tables can reach this size independently.

Examples

The following example sets the IP accounting threshold to only 500 entries:

ip accounting-threshold 500

Related Commands


Command	Description
clear ip accounting	Clears the active or checkpointed database when IP accounting is enabled.
ip accounting	Enables IP accounting on an interface.
ip accounting-list	Defines filters to control the hosts for which IP accounting information is kept.
ip accounting-transits	Controls the number of transit records that are stored in the IP accounting database.
show ip accounting	Displays the active accounting or checkpointed database or displays access list violations.

ip accounting-transits

To control the number of transit records that are stored in the IP accounting database, use the ip accounting-transits global configuration command. To return to the default number of records, use the no form of this command.

ip accounting-transits count

no ip accounting-transits

Syntax Description


count	Number of transit records to store in the IP accounting database.

Defaults

Command Modes

Global configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

Transit entries are those that do not match any of the filters specified by ip accounting-list global configuration commands. If no filters are defined, no transit entries are possible.

To maintain accurate accounting totals, the Cisco IOS software maintains two accounting databases: an active and a checkpointed database.

Examples

The following example specifies that no more than 100 transit records are stored:

ip accounting-transits 100

Related Commands


Command	Description
clear ip accounting	Clears the active or checkpointed database when IP accounting is enabled.
ip accounting	Enables IP accounting on an interface.
ip accounting-list	Defines filters to control the hosts for which IP accounting information is kept.
ip accounting-threshold	Sets the maximum number of accounting entries to be created.
show ip accounting	Displays the active accounting or checkpointed database or displays access list violations.

ip accounting mac-address

To enable IP accounting on a LAN interface based on the source and destination MAC address, use the ip accounting mac-address interface configuration command. To disable IP accounting based on the source and destination MAC address, use the noform of this command.

ip accounting mac-address {input | output]

no ip accounting mac-address {input | output]

Syntax Description


input	Performs accounting based on the source MAC address on received packets.
output	Performs accounting based on the destination MAC address on transmitted packets.

Defaults

Disabled

Command Modes

Interface configuration

Command History


Release	Modification
11.1CC	This command was introduced.

Usage Guidelines

This feature is supported on Ethernet, FastEthernet, and FDDI interfaces.

To display the MAC accounting information, use the show interface mac EXEC command.

MAC address accounting provides accounting information for IP traffic based on the source and destination MAC address on LAN interfaces. This calculates the total packet and byte counts for a LAN interface that receives or sends IP packets to or from a unique MAC address. It also records a timestamp for the last packet received or sent. With MAC address accounting, you can determine how much traffic is being sent to and/or received from various peers at NAPS/peering points.

Examples

The following example enables IP accounting based on the source and destination MAC address for received and transmitted packets:

interface ethernet 4/0/0

  ip accounting mac-address input

  ip accounting mac-address output

Related Commands


Command	Description
show interface mac	Displays MAC accounting information for interfaces configured for MAC accounting.

ip accounting precedence

To enable IP accounting on any interface based on IP precedence, use the ip accounting precedence interface configuration command. To disable IP accounting based on IP precedence, use the no form of this command.

ip accounting precedence {input | output]

no ip accounting precedence {input | output]

Syntax Description


input	Performs accounting based on IP precedence on received packets.
output	Performs accounting based on IP precedence on transmitted packets.

Defaults

Disabled

Command Modes

Interface configuration

Command History


Release	Modification
11.1CC	This command was introduced.

Usage Guidelines

To display IP precedence accounting information, use the show interface precedence EXEC command.

The precedence accounting feature provides accounting information for IP traffic, summarized by IP precedence value(s). This feature calculates the total packet and byte counts for an interface that receives or sends IP packets and sorts the results based on IP precedence. This feature is supported on all interfaces and subinterfaces and supports CEF, dCEF, flow, and optimum switching.

Examples

The following example enables IP accounting based on IP precedence for received and transmitted packets:

interface ethernet 4/0/0

  ip accounting precedence input

  ip accounting precedence output

Related Commands


Command	Description
show interface precedence	Displays precedence accounting information for an interface configured for precedence accounting.

ip drp access-group

To control the sources of Director Response Protocol (DRP) queries to the DRP Server Agent, use the ip drp access-group global configuration command. To remove the access list, use the no form of this command.

ip drp access-group access-list-number

no ip drp access-group access-list-number

Syntax Description


access-list-number	Number of a standard IP access list in the range 1 to 99 or from 1300 to 1999.

Defaults

The DRP Server Agent will answer all queries.

Command Modes

Global configuration

Command History


Release	Modification
11.2 F	This command was introduced.

Usage Guidelines

This command applies an access list to the interface, thereby controlling who can send queries to the DRP Server Agent.

If both an authentication key chain and an access group have been specified, both security measures must permit access before a request is processed.

Examples

The following example configures access list 1, which permits only queries from the host at 33.45.12.4:

access-list 1 permit 33.45.12.4

ip drp access-group 1

Related Commands


Command	Description
ip drp authentication key-chain	Configures authentication on the DRP Server Agent for DistributedDirector.
show ip drp	Displays information about the DRP Server Agent for DistributedDirector.

ip drp authentication key-chain

To configure authentication on the DRP Server Agent for DistributedDirector, use the ip drp authentication key-chain global configuration command. To remove the key chain, use the no form of this command.

ip drp authentication key-chain name-of-chain

no ip drp authentication key-chain name-of-chain

Syntax Description


name-of-chain	Name of the key chain containing one or more authentication keys.

Defaults

No authentication is configured for the DRP Server Agent.

Command Modes

Global configuration

Command History


Release	Modification
11.2 F	This command was introduced.

Usage Guidelines

When a key chain and key are configured, the key is used to authenticate all Director Response Protocol requests and responses. The active key on the DRP Server Agent must match the active key on the primary agent. Use the key and key-string commands to configure the key.

Examples

The following example configures a key chain named ddchain:

ip drp authentication key-chain ddchain

Related Commands


Command	Description
accept-lifetime	Sets the time period during which the authentication key on a key chain is received as valid.
ip drp access-group	Controls the sources of DRP queries to the DRP Server Agent.
key	Identifies an authentication key on a key chain.
key chain	Enables authentication for routing protocols.
key-string (authentication)	Specifies the authentication string for a key.
send-lifetime	Sets the time period during which an authentication key on a key chain is valid to be sent.
show ip drp	Displays information about the DRP Server Agent for DistributedDirector.
show key chain	Displays authentication key information.

ip drp server

To enable the Director Response Protocol (DRP) Server Agent that works with DistributedDirector, use the ip drp server global configuration command. To disable the DRP Server Agent, use the no form of this command.

ip drp server

no ip drp server

Syntax Description

This command has no arguments or keywords.

Defaults

Disabled

Command Modes

Global configuration

Command History


Release	Modification
11.2 F	This command was introduced.

Examples

The following example enables the DRP Server Agent:

ip drp server

Related Commands


Command	Description
ip drp access-group	Controls the sources of DRP queries to the DRP Server Agent.
ip drp authentication key-chain	Configures authentication on the DRP Server Agent for DistributedDirector.
show ip drp	Displays information about the DRP Server Agent for DistributedDirector.

ip icmp rate-limit unreachable

To have the Cisco IOS software limit the rate that Internet Control Message Protocol (ICMP) destination unreachable messages are generated, use the ip icmp rate-limit unreachable global configuration command. To remove the rate limit, use the no form of this command.

ip icmp rate-limit unreachable [df] milliseconds

no ip icmp rate-limit unreachable [df]

Syntax Description


df	(Optional) Limits the rate ICMP destination unreachable messages are sent when code 4, fragmentation is needed and DF set, is specified in the IP header of the ICMP destination unreachable message.
milliseconds	Time limit (in milliseconds) in which one ICMP destination unreachable message is sent. The range is 1 millisecond to 4294967295 milliseconds.

Defaults

The default value is one ICMP destination unreachable message per 500 milliseconds.

Command Modes

Global configuration

Command History


Release	Modification
12.0	This command was introduced.

Usage Guidelines

The no ip icmp rate-limit unreachable command turns off the previously configured rate limit. To re-set the rate limit to its default value, use the default ip icmp rate-limit unreachable command.

The Cisco IOS software maintains two timers: one for general destination unreachable messages and one for DF destination unreachable messages. Both share the same time limits and defaults. If the df option is not configured, the ip icmp rate-limit unreachable command sets the time values for DF destination unreachable messages. If the df option is configured, its time values remain independent from those of general destination unreachable messages.

Examples

The following example sets the rate of the ICMP destination unreachable message to one message every 10 milliseconds:

ip icmp rate-limit unreachable 10

The following example turns off the previously configured rate limit:

no ip icmp rate-limit unreachable

The following example sets the rate limit back to the default:

default ip icmp rate-limit unreachable

ip icmp redirect

To control the type of Internet Control Message Protocol (ICMP) redirect message that is sent by the Cisco IOS software, use the ip icmp redirect command in global configuration mode. To set the value back to the default, use the no form of this command.

ip icmp redirect [host | subnet]

no ip icmp redirect [host | subnet]

Syntax Description


host	(Optional) Sends ICMP host redirects.
subnet	(Optional) Sends ICMP subnet redirects.

Defaults

The router will send ICMP subnet redirect messages.

Because the ip icmp redirect subnet command is the default, the command will not be displayed in the configuration.

Command Modes

Global configuration

Command History


Release	Modification
12.0	This command was introduced.

Usage Guidelines

An ICMP redirect message can be generated by a router when a packet is received and transmitted on the same interface. In this situation, the router will forward the original packet and send a ICMP redirect message back to the sender of the original packet. This behavior allows the sender to bypass the router and forward future packets directly to the destination (or a router closer to the destination).

There are two types of ICMP redirect messages: redirect for a host address or redirect for an entire subnet.

The ip icmp redirect command determines the type of ICMP redirects sent by the system and is configured on a per system basis. Some hosts do not understand ICMP subnet redirects and need the router to send out ICMP host redirects. Use the ip icmp redirect host command to have the router send out ICMP host redirects. Use the ip icmp redirect subnet command to set the value back to the default, which is to send subnet redirects.

To prevent the router from sending ICMP redirects, use the no ip redirects interface configuration command.

Examples

The following example enables the router to send out ICMP host redirects:

ip icmp redirect hosts

The following example sets the value back to the default, which is subnet redirects:

ip icmp redirect subnet

Related Commands


Command	Description
ip redirects	Enables the sending of ICMP redirect messages.

ip mask-reply

To have the Cisco IOS software respond to Internet Control Message Protocol (ICMP) mask requests by sending ICMP Mask Reply messages, use the ip mask-reply interface configuration command. To disable this function, use the no form of this command.

ip mask-reply

no ip mask-reply

Syntax Description

This command has no arguments or keywords.

Defaults

Disabled

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.

Examples

The following example enables the sending of ICMP Mask Reply messages on Ethernet interface 0:

interface ethernet 0

 ip address 131.108.1.0 255.255.255.0

 ip mask-reply

ip mtu

To set the maximum transmission unit (MTU) size of IP packets sent on an interface, use the ip mtu interface configuration command. To restore the default MTU size, use the no form of this command.

ip mtu bytes

no ip mtu

Syntax Description


bytes	MTU in bytes.

Defaults

Minimum is 128 bytes; maximum depends on interface medium.

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

If an IP packet exceeds the MTU set for the interface, the Cisco IOS software will fragment it.

All devices on a physical medium must have the same protocol MTU in order to operate.

Note Changing the MTU value (with the mtu interface configuration command) can affect the IP MTU value. If the current IP MTU value is the same as the MTU value, and you change the MTU value, the IP MTU value will be modified automatically to match the new MTU. However, the reverse is not true; changing the IP MTU value has no effect on the value for the mtu command.

Examples

The following example sets the maximum IP packet size for the first serial interface to 300 bytes:

interface serial 0

 ip mtu 300

Related Commands


Command	Description
mtu	Adjusts the maximum packet size or MTU size.

ip redirects

To enable the sending of ICMP Redirect messages if the Cisco IOS software is forced to resend a packet through the same interface on which it was received, use the ip redirects interface configuration command. To disable the sending of redirect messages, use the no form of this command.

ip redirects

no ip redirects

Syntax Description

This command has no arguments or keywords.

Defaults

Enabled, unless Hot Standby Router Protocol is configured

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

If the Hot Standby Router Protocol is configured on an interface, ICMP Redirect messages are disabled by default for the interface.

Examples

The following example enables the sending of ICMP Redirect messages on Ethernet interface 0:

interface ethernet 0

 ip redirects

Related Commands


Command	Description
ip default-gateway	Defines a default gateway (router) when IP routing is disabled.
show ip redirects	Displays the address of a default gateway (router) and the address of hosts for which an ICMP Redirect message has been received.

ip source-route

To allow the Cisco IOS software to handle IP datagrams with source routing header options, use the ip source-route global configuration command. To have the software discard any IP datagram containing a source-route option, use the no form of this command.

ip source-route

no ip source-route

Syntax Description

This command has no arguments or keywords.

Defaults

Enabled

Command Modes

Global configuration

Command History


Release	Modification
10.0	This command was introduced.

Examples

The following example enables the handling of IP datagrams with source routing header options:

ip source-route

Related Commands


Command	Description
ping (privileged)	Diagnoses basic network connectivity on Apollo, AppleTalk, Connectionless Network Service (CLNS), DECnet, IP, Novell IPX, VINES, or XNS networks.
ping (user)	Diagnoses basic network connectivity on AppleTalk, CLNS, IP, Novell, Apollo, VINES, DECnet, or XNS networks.

ip tcp chunk-size

To alter the TCP maximum read size for Telnet or rlogin, use the ip tcp chunk-size global configuration command. To restore the default value, use the no form of this command.

ip tcp chunk-size characters

no ip tcp chunk-size

Syntax Description


characters	Maximum number of characters that Telnet or rlogin can read in one read instruction. The default value is 0, which Telnet and rlogin interpret as the largest possible 32-bit positive number.

Defaults

0, which Telnet and rlogin interpret as the largest possible 32-bit positive number.

Command Modes

Global configuration

Command History


Release	Modification
9.1	This command was introduced.

Usage Guidelines

It is unlikely you will need to change the default value.

Examples

The following example sets the maximum TCP read size to 64000 bytes:

ip tcp chunk-size 64000

ip tcp compression-connections

To specify the total number of header compression connections that can exist on an interface, use the ip tcp compression-connections interface configuration command. To restore the default, use the no form of this command.

ip tcp compression-connections number

no ip tcp compression-connections number

Syntax Description


number	Number of connections the cache supports. It can be a number from 3 to 256.

Defaults

16 connections

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

You should configure one connection for each TCP connection through the specified interface.

Each connection sets up a compression cache entry, so you are in effect specifying the maximum number of cache entries and the size of the cache. Too few cache entries for the specified interface can lead to degraded performance, while too many cache entries can lead to wasted memory.

Note Both ends of the serial connection must use the same number of cache entries.

Examples

The following example sets the first serial interface for header compression with a maximum of ten cache entries:

interface serial 0

 ip tcp header-compression

 ip tcp compression-connections 10

Related Commands


Command	Description
ip tcp header-compression	Enables TCP header compression.
show ip tcp header-compression	Displays statistics about TCP header compression.

ip tcp header-compression

To enable TCP header compression, use the ip tcp header-compression interface configuration command. To disable compression, use the no form of this command.

ip tcp header-compression [passive]

no ip tcp header-compression [passive]

Syntax Description


passive	(Optional) Compresses outgoing TCP packets only if incoming TCP packets on the same interface are compressed. If you do not specify the passive keyword, the Cisco IOS software compresses all traffic.

Defaults

Disabled

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

You can compress the headers of your TCP/IP packets in order to reduce the size of your packets. TCP header compression is supported on serial lines using Frame Relay, HDLC or Point-to-Point (PPP) encapsulation. You must enable compression on both ends of a serial connection. RFC 1144 specifies the compression process. Compressing the TCP header can speed up Telnet connections dramatically. In general, TCP header compression is advantageous when your traffic consists of many small packets, not for traffic that consists of large packets. Transaction processing (usually using terminals) tends to use small packets while file transfers use large packets. This feature only compresses the TCP header, so it has no effect on UDP packets or other protocol headers.

When compression is enabled, fast switching is disabled. This means that fast interfaces like T1 can overload the router. Consider your network’s traffic characteristics before using this command.

Examples

The following example sets the first serial interface for header compression with a maximum of ten cache entries:

interface serial 0

 ip tcp header-compression

 ip tcp compression-connections 10

Related Commands


Command	Description
ip tcp compression-connections	Specifies the total number of header compression connections that can exist on an interface.

ip tcp path-mtu-discovery

To enable Path MTU Discovery for all new TCP connections from the router, use the ip tcp path-mtu-discovery global configuration command. To disable the function, use the no form of this command.

ip tcp path-mtu-discovery [age-timer {minutes | infinite}]

no ip tcp path-mtu-discovery [age-timer {minutes | infinite}]

Syntax Description


age-timerminutes	(Optional) Time interval (in minutes) after which TCP re-estimates the Path MTU with a larger maximum segment size (MSS). The maximum is 30 minutes; the default is 10 minutes.
age-timer infinite	(Optional) Turns off the age-timer.

Defaults

Disabled. If enabled, default minutes is 10 minutes.

Command Modes

Global configuration

Command History


Release	Modification
10.3	This command was introduced.
11.2	The following keywords were added: •age-timer •infinite

Usage Guidelines

Path MTU Discovery is a method for maximizing the use of available bandwidth in the network between the end points of a TCP connection. It is described in RFC 1191. Existing connections are not affected when this feature is turned on or off.

Customers using TCP connections to move bulk data between systems on distinct subnets would benefit most by enabling this feature. This might include customers using RSRB with TCP encapsulation, STUN, X.25 Remote Switching (also known as XOT, or X.25 over TCP), and some protocol translation configurations.

The age timer is a time interval for how often TCP re-estimates the Path MTU with a larger MSS. By using the age timer, TCP Path MTU becomes a dynamic process. If MSS used for the connection is smaller than what the peer connection can handle, a larger MSS is tried every time the age timer expires. The discovery process is stopped when either the send MSS is as large as the peer negotiated, or the user has disabled the timer on the router. You can turn off the age-timer by setting it to infinite.

Examples

The following example enables Path MTU Discovery:

ip tcp path-mtu-discovery

ip tcp queuemax

To alter the maximum TCP outgoing queue per connection, use the ip tcp queuemax global configuration command. To restore the default value, use the no form of this command.

ip tcp queuemax packets

no ip tcp queuemax

Syntax Description


packets	Outgoing queue size of TCP packets. The default value is 5 segments if the connection has a TTY associated with it. If there is no TTY associated with it, the default value is 20 segments.

Defaults

The default value is 5 segments if the connection has a TTY associated with it. If there is no TTY associated with it, the default value is 20 segments.

Command Modes

Global configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

Changing the default value changes the 5 segments, not the 20 segments.

Examples

The following example sets the maximum TCP outgoing queue to 10 packets:

ip tcp queuemax 10

ip tcp selective-ack

To enable TCP selective acknowledgment, use the ip tcp selective-ack global configuration command. To disable TCP selective acknowledgment, use the no form of this command.

ip tcp selective-ack

no ip tcp selective-ack

Syntax Description

This command has no arguments or keywords.

Defaults

Disabled

Command Modes

Global configuration

Command History


Release	Modification
11.2 F	This command was introduced.

Usage Guidelines

TCP might not experience optimal performance if multiple packets are lost from one window of data. With the limited information available from cumulative acknowledgments, a TCP sender can learn about only one lost packet per round trip time. An aggressive sender could retransmit packets early, but such retransmitted segments might have already been successfully received.

The TCP selective acknowledgment mechanism helps overcome these limitations. The receiving TCP returns selective acknowledgment packets to the sender, informing the sender about data that has been received. The sender can then retransmit only the missing data segments.

TCP selective acknowledgment improves overall performance. The feature is used only when multiple packets drop from a TCP window. There is no performance impact when the feature is enabled but not used.

This command becomes effective only on new TCP connections opened after the feature is enabled.

This feature must be disabled if you want TCP header compression. You might disable this feature if you have severe TCP problems.

Refer to RFC 2018 for more detailed information on TCP selective acknowledgment.

Examples

The following example enables the router to send and receive TCP selective acknowledgments:

ip tcp selective-ack

Related Commands


Command	Description
ip tcp header-compression	Enables TCP header compression.

ip tcp synwait-time

To set a period of time the Cisco IOS software waits while attempting to establish a TCP connection before it times out, use the ip tcp synwait-time global configuration command. To restore the default time, use the no form of this command.

ip tcp synwait-time seconds

no ip tcp synwait-time seconds

Syntax Description


seconds	Time in seconds the software waits while attempting to establish a TCP connection. It can be an integer from 5 to 300 seconds. The default is 30 seconds.

Defaults

30 seconds

Command Modes

Global configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

In versions previous to Cisco IOS software 10.0, the system would wait a fixed 30 seconds when attempting to establish a TCP connection. If your network contains Public Switched Telephone Network (PSTN) dial-on-demand routing (DDR), the call setup time may exceed 30 seconds. This amount of time is not sufficient in networks that have dial-up asynchronous connections because it will affect your ability to Telnet over the link (from the router) if the link must be brought up. If you have this type of network, you might want to set this value to the UNIX value of 75.

Because this is a host parameter, it does not pertain to traffic going through the router, just for traffic originated at this device. Because UNIX has a fixed 75-second timeout, hosts are unlikely to see this problem.

Examples

The following example configures the Cisco IOS software to continue attempting to establish a TCP connection for 180 seconds:

ip tcp synwait-time 180

ip tcp timestamp

To enable TCP timestamp, use the ip tcp timestamp global configuration command. To disable TCP timestamp, use the no form of this command.

ip tcp timestamp

no ip tcp timestamp

Syntax Description

This command has no arguments or keywords.

Defaults

Disabled

Command Modes

Global configuration

Command History


Release	Modification
11.2 F	This command was introduced.

Usage Guidelines

TCP timestamp improves round-trip time estimates. Refer to RFC 1323 for more detailed information on TCP timestamp.

This feature must be disabled if you want to use TCP header compression.

Examples

The following example enables the router to send TCP timestamps:

ip tcp timestamp

Related Commands


Command	Description
ip tcp header-compression	Enables TCP header compression.

ip tcp window-size

To alter the TCP window size, use the ip tcp window-size global configuration command. To restore the default value, use the noform of this command.

ip tcp window-size bytes

no ip tcp window-size

Syntax Description


bytes	Window size in bytes. The maximum is 65535 bytes. The default value is 2144 bytes.

Defaults

2144 bytes

Command Modes

Global configuration

Command History


Release	Modification
9.1	This command was introduced.

Usage Guidelines

Do not use this command unless you clearly understand why you want to change the default value.

If your TCP window size is set to 1000 bytes, for example, you could have 1 packet of 1000 bytes or 2 packets of 500 bytes, and so on. However, there is also a limit on the number of packets allowed in the window. There can be a maximum of 5 packets if the connection has TTY; otherwise there can be 20 packets.

Examples

The following example sets the TCP window size to 1000 bytes:

ip tcp window-size 1000

ip unreachables

To enable the generation of ICMP Unreachable messages, use the ip unreachables interface configuration command. To disable this function, use the no form of this command.

ip unreachables

no ip unreachables

Syntax Description

This command has no arguments or keywords.

Defaults

Enabled

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

If the Cisco IOS software receives a nonbroadcast packet destined for itself that uses a protocol it does not recognize, it sends an ICMP Protocol Unreachable message to the source.

If the software receives a datagram that it cannot deliver to its ultimate destination because it knows of no route to the destination address, it replies to the originator of that datagram with an ICMP Host Unreachable message.

This command affects all kinds of ICMP unreachable messages.

Examples

The following example enables the generation of ICMP Unreachable messages, as appropriate, on an interface:

interface ethernet 0

 ip unreachables

permit (IP)

To set conditions for a named IP access list, use the permit access-list configuration command. To remove a condition from an access list, use the no form of this command.

permit {source [source-wildcard] | any} [log]

no permit {source [source-wildcard] | any}

permit protocol source source-wildcard destination destination-wildcard [precedence precedence] [tos tos] [log]

no permit protocol source source-wildcard destination destination-wildcard [precedence precedence] [tos tos] [log] [fragments]

ICMP

permit icmp source source-wildcard destination destination-wildcard [icmp-type [icmp-code] | icmp-message] [precedenceprecedence] [tos tos] [log] [fragments]

IGMP

permit igmp source source-wildcard destination destination-wildcard [igmp-type] [precedence precedence] [tos tos] [log] [fragments]

TCP

permit tcp source source-wildcard [operator port [port]] destination destination-wildcard [operator port [port]] [established] [precedence precedence] [tos tos] [log] [fragments]

UDP

permit udp source source-wildcard [operator port [port]] destination destination-wildcard [operator port [port]] [precedenceprecedence] [tos tos] [log] [fragments]

Syntax Description


source	Number of the network or host from which the packet is being sent. There are two alternative ways to specify the source: Use a 32-bit quantity in four-part, dotted-decimal format. Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255.
source-wildcard	(Optional) Wildcard bits to be applied to the source. There are two alternative ways to specify the source wildcard: Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255.
protocol	Name or number of an IP protocol. It can be one of the keywords eigrp, gre, icmp,igmp, igrp, ip, ipinip, nos, ospf, tcp, or udp, or an integer in the range 0 to 255 representing an IP protocol number. To match any Internet protocol (including ICMP, TCP, and UDP), use the keyword ip. Some protocols allow further qualifiers described later.
source	Number of the network or host from which the packet is being sent. There are three alternative ways to specify the source: •Use a 32-bit quantity in four-part, dotted-decimal format. •Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255. •Use host source as an abbreviation for a source and source-wildcard of source0.0.0.0.
source-wildcard	Wildcard bits to be applied to source. There are three alternative ways to specify the source wildcard: •Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. •Use the keyword any as an abbreviation for a source and source-wildcard of 0.0.0.0 255.255.255.255. •Use host source as an abbreviation for a source and source-wildcard of source0.0.0.0.
destination	Number of the network or host to which the packet is being sent. There are three alternative ways to specify the destination: •Use a 32-bit quantity in four-part, dotted-decimal format. •Use the keyword any as an abbreviation for the destination and destination-wildcardof 0.0.0.0 255.255.255.255. •Use host destination as an abbreviation for a destination and destination-wildcard ofdestination 0.0.0.0.
destination-wildcard	Wildcard bits to be applied to the destination. There are three alternative ways to specify the destination wildcard: •Use a 32-bit quantity in four-part, dotted-decimal format. Place ones in the bit positions you want to ignore. •Use the keyword any as an abbreviation for a destination and destination-wildcard of 0.0.0.0 255.255.255.255. •Use host destination as an abbreviation for a destination and destination-wildcard ofdestination 0.0.0.0.
precedenceprecedence	(Optional) Packets can be filtered by precedence level, as specified by a number from 0 to 7 or by name as listed in the section “Usage Guidelines.”
tos tos	(Optional) Packets can be filtered by type of service level, as specified by a number from 0 to 15 or by name as listed in the “Usage Guidelines” section of the access-list (IP extended) command.
icmp-type	(Optional) ICMP packets can be filtered by ICMP message type. The type is a number from 0 to 255.
icmp-code	(Optional) ICMP packets which are filtered by ICMP message type can also be filtered by the ICMP message code. The code is a number from 0 to 255.
icmp-message	(Optional) ICMP packets can be filtered by an ICMP message type name or ICMP message type and code name. The possible names are found in the “Usage Guidelines” section of the access-list (IP extended) command.
igmp-type	(Optional) IGMP packets can be filtered by IGMP message type or message name. A message type is a number from 0 to 15. IGMP message names are listed in the “Usage Guidelines” section of the access-list (IP extended) command.
operator	(Optional) Compares source or destination ports. Possible operands include lt (less than),gt (greater than), eq (equal), neq (not equal), and range (inclusive range). If the operator is positioned after the source and source-wildcard, it must match the source port. If the operator is positioned after the destination and destination-wildcard, it must match the destination port. The range operator requires two port numbers. All other operators require one port number.
port	(Optional) The decimal number or name of a TCP or UDP port. A port number is a number from 0 to 65535. TCP and UDP port names are listed in the “Usage Guidelines” section of the access-list (IP extended) command. TCP port names can only be used when filtering TCP. UDP port names can only be used when filtering UDP.
established	(Optional) For the TCP protocol only: Indicates an established connection. A match occurs if the TCP datagram has the ACK or RST bits set. The nonmatching case is that of the initial TCP datagram to form a connection.
log	(Optional) Causes an informational logging message about the packet that matches the entry to be sent to the console. (The level of messages logged to the console is controlled by the logging console command.) The message for a standard list includes the access list number, whether the packet was permitted or denied, the source address, and the number of packets. The message for an extended list includes the access list number; whether the packet was permitted or denied; the protocol; whether it was TCP, UDP, ICMP, or a number; and, if appropriate, the source and destination addresses and source and destination port numbers. For both standard and extended lists, the message is generated for the first packet that matches, and then at 5-minute intervals, including the number of packets permitted or denied in the prior 5-minute interval. The logging facility might drop some logging message packets if there are too many to be handled or if there is more than one logging message to be handled in 1 second. This behavior prevents the router from crashing due to too many logging packets. Therefore, the logging facility should not be used as a billing tool or an accurate source of the number of matches to an access list.
fragments	(Optional) The access list entry applies to noninitial fragments of packets; the fragment is either permitted or denied accordingly. For more details about the fragments keyword, see the “Access List Processing of Fragments” and “Fragments and Policy Routing” sections in the “Usage Guidelines” section.

Defaults

There are no specific conditions under which a packet passes the named access list.

Command Modes

Access-list configuration

Command History


Release	Modification
11.2	This command was introduced.
11.3(3)T	The log keyword for a standard access list was added.
12.0(11)	The fragments keyword was added.

Usage Guidelines

Use this command following the ip access-list command to define the conditions under which a packet passes the access list.

Access List Processing of Fragments

The behavior of access-list entries regarding the use or lack of the fragments keyword can be summarized as follows:


If the Access-List Entry has…	Then..
…no fragments keyword (the default behavior), and assuming all of the access-list entry information matches,	For an access-list entry containing only Layer 3 information: •The entry is applied to nonfragmented packets, initial fragments and noninitial fragments. For an access list entry containing Layer 3 and Layer 4 information: •The entry is applied to nonfragmented packets and initial fragments. –If the entry is a permit statement, the packet or fragment is permitted. –If the entry is a deny statement, the packet or fragment is denied. •The entry is also applied to noninitial fragments in the following manner. Because noninitial fragments contain only Layer 3 information, only the Layer 3 portion of an access-list entry can be applied. If the Layer 3 portion of the access-list entry matches, and –If the entry is a permit statement, the noninitial fragment is permitted. –If the entry is a deny statement, the next access-list entry is processed. Note The deny statements are handled differently for noninitial fragments versus nonfragmented or initial fragments.
…the fragments keyword, and assuming all of the access-list entry information matches,	The access-list entry is applied only to noninitial fragments. Note The fragments keyword cannot be configured for an access-list entry that contains any Layer 4 information.

Packet fragments of IP datagrams are considered individual packets and each counts individually as a packet in access list accounting and access list violation counts.

Note The fragments keyword cannot solve all cases involving access lists and IP fragments.

Fragments and Policy Routing

Examples

The following example sets conditions for a standard access list named Internetfilter:

ip access-list standard Internetfilter

 deny 192.5.34.0  0.0.0.255

 permit 128.88.0.0  0.0.255.255

 permit 36.0.0.0  0.255.255.255

! (Note: all other access implicitly denied)

Related Commands


Command	Description
deny (IP)	Sets conditions for a named IP access list.
ip access-group	Controls access to an interface.
ip access-list	Defines an IP access list by name.
show access-lists	Displays the contents of all current IP access lists.

show access-lists

To display the contents of current access lists, use the show access-lists privileged EXEC command.

show access-lists [access-list-number | name]

Syntax Description


access-list-number	(Optional) Number of the access list to display. The system displays all access lists by default.
name	(Optional) Name of the IP access list to display.

Defaults

The system displays all access lists.

Command Modes

Privileged EXEC

Examples

The following is sample output from the show access-lists command when access list 101 is specified:

Router# show access-lists 101

Extended IP access list 101

    permit tcp host 198.92.32.130 any established (4304 matches)

    permit udp host 198.92.32.130 any eq domain (129 matches)

    permit icmp host 198.92.32.130 any

    permit tcp host 198.92.32.130 host 171.69.2.141 gt 1023

    permit tcp host 198.92.32.130 host 171.69.2.135 eq smtp (2 matches)

    permit tcp host 198.92.32.130 host 198.92.30.32 eq smtp

    permit tcp host 198.92.32.130 host 171.69.108.33 eq smtp

    permit udp host 198.92.32.130 host 171.68.225.190 eq syslog

    permit udp host 198.92.32.130 host 171.68.225.126 eq syslog

    deny   ip 150.136.0.0 0.0.255.255 224.0.0.0 15.255.255.255

    deny   ip 171.68.0.0 0.1.255.255 224.0.0.0 15.255.255.255 (2 matches)

    deny   ip 172.24.24.0 0.0.1.255 224.0.0.0 15.255.255.255

    deny   ip 192.82.152.0 0.0.0.255 224.0.0.0 15.255.255.255

    deny   ip 192.122.173.0 0.0.0.255 224.0.0.0 15.255.255.255

    deny   ip 192.122.174.0 0.0.0.255 224.0.0.0 15.255.255.255

    deny   ip 192.135.239.0 0.0.0.255 224.0.0.0 15.255.255.255

    deny   ip 192.135.240.0 0.0.7.255 224.0.0.0 15.255.255.255

    deny   ip 192.135.248.0 0.0.3.255 224.0.0.0 15.255.255.255

    deny   ip 192.150.42.0 0.0.0.255 224.0.0.0 15.255.255.255

An access list counter counts how many packets are allowed by each line of the access list. This number is displayed as the number of matches.

For information on how to configure access lists, refer to the “Configuring IP Services” chapter of the Network Protocols Configuration Guide, Part 1.

For information on how to configure dynamic access lists, refer to the “Traffic Filtering and Firewalls” chapter of the Security Configuration Guide.

Related Commands

Command	Description
access-list (IP extended)	Defines an extended IP access list.
access-list (IP standard)	Defines a standard IP access list.
clear access-list counters	Clears the counters of an access list.
clear access-template	Clears a temporary access list entry from a dynamic access list manually.
ip access-list	Defines an IP access list by name.
show access-lists	Displays the contents of all current IP access lists.

show interface mac

To display MAC accounting information for interfaces configured for MAC accounting, use the show interface mac EXEC command.

show interface [type number] mac

Syntax Description


type	(Optional) Interface type supported on your router.
number	(Optional) Port number of the interface. The syntax varies depending on the type router. For example, on a Cisco 7500 series router the syntax is 0/0/0, where 0 represents the slot, port adapter, and port number (the slash is required). Refer to the appropriate hardware manual for numbering information.

Command Modes

EXEC

Command History

Release	Modification
11.1 CC	This command was introduced.

Usage Guidelines

The show interface mac command displays information for all interfaces configured for MAC accounting. To display information for a single interface, use the show interface type number mac command.

For incoming packets on the interface, the accounting statistics are gathered before the CAR/DCAR feature is performed on the packet. For outgoing packets on the interface, the accounting statistics are gathered after output CAR, before output DCAR or DWRED or DWFQ feature is performed on the packet. Therefore, if a you are using DCAR or DWRED on the interface and packets are dropped, the dropped packets are still counted in the show interface mac command because the calculations are done prior to the features.

The maximum number of MAC addresses that can be stored for the input address is 512 and the maximum number of MAC address that can be stored for the output address is 512. After the maximum is reached, subsequent MAC addresses are ignored.

To clear the accounting statistics, use the clear counter EXEC command.To configure an interface for IP accounting based on the MAC address, use the ip accounting mac-address interface configuration command.

Examples

The following is sample output from the show interface mac command. This feature calculates the total packet and byte counts for the interface that receives (input) or sends (output) IP packets to or from a unique MAC address. It also records a timestamp for the last packet received or sent.

Router# show interface ethernet 0/1/1 mac

Ethernet0/1/1

  Input  (511 free)

    0007.f618.4449(228):  4 packets, 456 bytes, last: 2684ms ago

                  Total:  4 packets, 456 bytes

  Output  (511 free)

    0007.f618.4449(228):  4 packets, 456 bytes, last: 2692ms ago

                  Total:  4 packets, 456 bytes

Related Commands

Command	Description
ip accounting mac-address	Enables IP accounting on any interface based on the source and destination MAC address.

show interface precedence

To display precedence accounting information for interfaces configured for precedence accounting, use the show interface macEXEC command.

show interface [type number] precedence

Syntax Description


type	(Optional) Interface type supported on your router.
number	(Optional) Port number of the interface. The syntax varies depending on the type router. For example, on a Cisco 7500 series router the syntax is 0/0/0, where 0 represents the slot, port adapter, and port number (the slash is required). Refer to the appropriate hardware manual for numbering information.

Command Modes

EXEC

Command History

Release	Modification
11.1 CC	This command was introduced.

Usage Guidelines

The show interface precedence command displays information for all interfaces configured for IP precedence accounting. To display information for a single interface, use the show interface type number precedence command.

For incoming packets on the interface, the accounting statistics are gathered before input CAR/DCAR is performed on the packet. Therefore, if CAR/DCAR changes the precedence on the packet, it is counted based on the old precedence setting with the show interface precedence command.

For outgoing packets on the interface, the accounting statistics are gathered after output DCAR or DWRED or DWFQ feature is performed on the packet.

To clear the accounting statistics, use the clear counter EXEC command.

To configure an interface for IP accounting based on IP precedence, use the ip accounting precedence interface configuration command.

Examples

The following is sample output from the show interface precedence command. This feature calculates the total packet and byte counts for the interface that receives (input) or sends (output) IP packets and sorts the results based on IP precedence.

Router# show interface ethernet 0/1/1 precedence

Ethernet0/1/1

  Input

    Precedence 0:  4 packets, 456 bytes

  Output

    Precedence 0:  4 packets, 456 bytes

Related Commands

Command	Description
ip accounting precedence	Enables IP accounting on any interface based on IP precedence.

show ip access-list

To display the contents of all current IP access lists, use the show ip access-list EXEC command.

show ip access-list [access-list-number | name]

Syntax Description


access-list-number	(Optional) Number of the IP access list to display.
name	(Optional) Name of the IP access list to display.

Defaults

Displays all standard and extended IP access lists.

Command Modes

EXEC

Command History


Release	Modification
10.3	This command was introduced.

Usage Guidelines

The show ip access-list command provides output identical to the show access-lists command, except that it is IP-specific and allows you to specify a particular access list.

Examples

The following is sample output from the show ip access-list command when all are requested:

Router# show ip access-list

Extended IP access list 101

          deny udp any any eq ntp

          permit tcp any any

          permit udp any any eq tftp

          permit icmp any any

          permit udp any any eq domain

The following is sample output from the show ip access-list command when the name of a specific access list is requested:

Router# show ip access-list Internetfilter

Extended IP access list Internetfilter

    permit tcp any 171.69.0.0 0.0.255.255 eq telnet

    deny tcp any any

    deny udp any 171.69.0.0 0.0.255.255 lt 1024

    deny ip any any log

show ip accounting

To display the active accounting or checkpointed database or to display access list violations, use the show ip accounting EXEC command.

show ip accounting [checkpoint] [output-packets | access-violations]

Syntax Description


checkpoint	(Optional) Indicates that the checkpointed database should be displayed.
output-packets	(Optional) Indicates that information pertaining to packets that passed access control and were successfully routed should be displayed. If neither the output-packets nor access-violations keyword is specified, output-packets is the default.
access-violations	(Optional) Indicates that information pertaining to packets that failed access lists and were not routed should be displayed. If neither the output-packets nor access-violationskeyword is specified, output-packets is the default.

Defaults

If neither the output-packets nor access-violations keyword is specified, show ip accounting displays information pertaining to packets that passed access control and were successfully routed.

Command Modes

EXEC

Command History


Release	Modification
10.0	This command was introduced.
10.3	The following keywords were added: •output-packets •access-violations

Usage Guidelines

If you do not specify any keywords, the show ip accounting command displays information about the active accounting database, and traffic coming from a remote site and transiting through a router.

To display IP access violations, you must give the access-violations keyword on the command. If you do not specify the keyword, the command defaults to displaying the number of packets that have passed access lists and were routed.

To use this command, you must first enable IP accounting on a per-interface basis.

Examples

The following is sample output from the show ip accounting command:

Router# show ip accounting

   Source           Destination              Packets               Bytes

 131.108.19.40    192.67.67.20                     7                 306

 131.108.13.55    192.67.67.20                    67                2749

 131.108.2.50     192.12.33.51                    17                1111

 131.108.2.50     130.93.2.1                       5                 319

 131.108.2.50     130.93.1.2                     463               30991

 131.108.19.40    130.93.2.1                       4                 262

 131.108.19.40    130.93.1.2                      28                2552

 131.108.20.2     128.18.6.100                    39                2184

 131.108.13.55    130.93.1.2                      35                3020

 131.108.19.40    192.12.33.51                  1986               95091

 131.108.2.50     192.67.67.20                   233               14908

 131.108.13.28    192.67.67.53                   390               24817

 131.108.13.55    192.12.33.51                214669             9806659

 131.108.13.111   128.18.6.23                  27739             1126607

 131.108.13.44    192.12.33.51                 35412             1523980

 192.31.7.21      130.93.1.2                      11                 824

 131.108.13.28    192.12.33.2                     21                1762

 131.108.2.166    192.31.7.130                   797              141054

 131.108.3.11     192.67.67.53                     4                 246

 192.31.7.21      192.12.33.51                 15696              695635

 192.31.7.24      192.67.67.20                    21                 916

 131.108.13.111   128.18.10.1                     16                1137

 accounting threshold exceeded for 7 packets and 433 bytes

The following is sample output from the show ip accounting access-violations command. The output pertains to packets that failed access lists and were not routed:

Router# show ip accounting access-violations

   Source           Destination      Packets        Bytes        ACL

131.108.19.40    192.67.67.20              7          306         77

131.108.13.55    192.67.67.20             67         2749        185

131.108.2.50     192.12.33.51             17         1111        140

131.108.2.50     130.93.2.1                5          319        140

131.108.19.40    130.93.2.1                4          262         77

Accounting data age is 41

The following is sample output from the show ip accounting command. The output shows the original source and destination addresses that are separated by three routers:

Router3# show ip accounting

Source                  Destination                  Packets                  Bytes

10.225.231.154          172.16.10.2                  44                       28160

10.76.97.34             172.16.10.2                  44                       28160

10.10.11.1              172.16.10.2                  507                      324480

10.10.10.1              172.16.10.2                  507                      318396

10.100.45.1             172.16.10.2                  508                      325120

10.98.32.5              172.16.10.2                  44                       28160

Accounting data age is 2

Table 11 describes the fields shown in the displays.

Table 11 show ip accounting (and access-violation) Field Descriptions
Field	Description
Source	Source address of the packet.
Destination	Destination address of the packet.
Packets	Number of packets transmitted from the source address to the destination address. With the access-violations keyword, the number of packets transmitted from the source address to the destination address that violated an access control list.
Bytes	Sum of the total number of bytes (IP header and data) of all IP packets transmitted from the source address to the destination address. With the access-violations keyword, the total number of bytes transmitted from the source address to the destination address that violated an access-control list.
ACL	Number of the access list of the last packet transmitted from the source to the destination that failed an access list filter.
accounting threshold exceeded…	Data for all packets that could not be entered into the accounting table when the accounting table is full. This data is combined into a single entry.

Related Commands


Command	Description
clear ip accounting	Clears the active or checkpointed database when IP accounting is enabled.
ip accounting	Enables IP accounting on an interface.
ip accounting-list	Defines filters to control the hosts for which IP accounting information is kept.
ip accounting-threshold	Sets the maximum number of accounting entries to be created.
ip accounting-transits	Controls the number of transit records that are stored in the IP accounting database.

show ip drp

To display information about the DRP Server Agent for DistributedDirector, use the show ip drp EXEC command.

show ip drp

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History


Release	Modification
11.2 F	This command was introduced.

Examples

The following is sample output from the show ip drp command:

Router# show ip drp

Director Responder Protocol Agent is enabled

717 director requests, 712 successful lookups, 5 failures, 0 no route

Authentication is enabled, using "test" key-chain

Table 12 describes the significant fields in the display.

Table 12 show ip drp Field Descriptions
Field	Description
director requests	Number of DRP requests that have been received (including any using authentication key-chain encryption that failed).
successful lookups	Number of successful DRP lookups that produced responses.
failures	Number of DRP failures (for various reasons including authentication key-chain encryption failures).

Related Commands


Command	Description
ip drp access-group	Controls the sources of DRP queries to the DRP Server Agent.
ip drp authentication key-chain	Configures authentication on the DRP Server Agent for DistributedDirector.

show ip redirects

To display the address of a default gateway (router) and the address of hosts for which an ICMP Redirect messages has been received, use the show ip redirects EXEC command.

show ip redirects

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

This command displays the default router (gateway) as configured by the ip default-gateway command.

The ip redirects command enables the router to send ICMP Redirect messages.

Examples

The following is sample output from the show ip redirects command:

Router# show ip redirects

Default gateway is 160.89.80.29

Host               Gateway           Last Use    Total Uses  Interface

131.108.1.111      160.89.80.240         0:00             9  Ethernet0

128.95.1.4         160.89.80.240         0:00             4  Ethernet0

Router#

Related Commands


Command	Description
ip default-gateway	Defines a default gateway (router) when IP routing is disabled.
ip redirects	Enables the sending of ICMP Redirect messages if the Cisco IOS software is forced to resend a packet through the same interface on which it was received.

show ip sockets

To display IP socket information, use the show ip sockets command in privileged EXEC mode or user EXEC mode.

show ip sockets

Syntax Description

This command has no keywords or arguments.

Defaults

No default behavior or values.

Command Modes

Privileged EXEC
User EXEC

Command History


Release	Modification
10.0 T	This command was introduced.

Usage Guidelines

Use this command to verify that the socket being used is opening correctly. If there is a local and remote endpoint, a connection is established with the ports indicated.

Examples

The following is sample output from the show ip sockets command:

Router# show ip sockets

Proto    Remote      Port      Local         Port  In Out Stat TTY OutputIF

 17      0.0.0.0        0    171.68.186.193    67   0   0    1   0

 17   171.68.191.135  514    171.68.191.129  1811   0   0    0   0

 17   172.16.135.20   514    171.68.191.1    4125   0   0    0   0

 17   171.68.207.163   49    171.68.186.193    49   0   0    9   0

 17      0.0.0.0      123    171.68.186.193   123   0   0    1   0

 88      0.0.0.0        0    171.68.186.193   202   0   0    0   0

 17   172.16.96.59  32856    171.68.191.1     161   0   0    1   0

 17     --listen--             --any--        496   0   0    1   0

Table 13 describes the significant fields shown in the display.

Table 13 show ip sockets Field Descriptions
Field	Description
Proto	Protocol type, for example, User Datagram Protocol (UDP) or TCP.
Remote	Remote address connected to this networking device. If the remote address is considered illegal, “–listen–” is displayed.
Port	Remote port. If the remote address is considered illegal, “–listen–” is displayed.
Local	Local address. If the local address is considered illegal or is the address 0.0.0.0, “–any–” displays.
Port	Local port.
In	Input queue size.
Out	Output queue size.
Stat	Various statistics for a socket.
TTY	The tty number for the creator of this socket.
OutputIF	Output IF string, if one exists.

show ip tcp header-compression

To display statistics about TCP header compression, use the show ip tcp header-compression EXEC command.

show ip tcp header-compression

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History


Release	Modification
10.0	This command was introduced.

Examples

The following is sample output from the show ip tcp header-compression command:

Router# show ip tcp header-compression

TCP/IP header compression statistics:

  Interface Serial1: (passive, compressing)

    Rcvd:    4060 total, 2891 compressed, 0 errors

             0 dropped, 1 buffer copies, 0 buffer failures

    Sent:    4284 total, 3224 compressed,

             105295 bytes saved, 661973 bytes sent

             1.15 efficiency improvement factor

    Connect:  16 slots, 1543 long searches, 2 misses, 99% hit ratio

             Five minute miss rate 0 misses/sec, 0 max misses/sec

Table 14 describes significant fields shown in the display.

Table 14 show ip tcp header-compression Field Descriptions
Field	Description
Rcvd:
total	Total number of TCP packets received.
compressed	Total number of TCP packets compressed.
errors	Unknown packets.
dropped	Number of packets dropped due to invalid compression.
buffer copies	Number of packets that had to be copied into bigger buffers for decompression.
buffer failures	Number of packets dropped due to a lack of buffers.
Sent:
total	Total number of TCP packets sent.
compressed	Total number of TCP packets compressed.
bytes saved	Number of bytes reduced.
bytes sent	Number of bytes sent.
efficiency improvement factor	Improvement in line efficiency because of TCP header compression.
Connect:
slots	Size of the cache.
long searches	Indicates the number of times the software had to look to find a match.
misses	Indicates the number of times a match could not be made. If your output shows a large miss rate, then the number of allowable simultaneous compression connections may be too small.
hit ratio	Percentage of times the software found a match and was able to compress the header.
Five minute miss rate	Calculates the miss rate over the previous 5 minutes for a longer-term (and more accurate) look at miss rate trends.
max misses/sec	Maximum value of the previous field.

Related Commands


Command	Description
ip tcp header-compression	Enables TCP header compression.

show ip traffic

To display statistics about IP traffic, use the show ip traffic EXEC command.

show ip traffic

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History


Release	Modification
10.0	This command was introduced.

Examples

The following is sample output from the show ip traffic command:

Router# show ip traffic

IP statistics:

   Rcvd:  98 total, 98 local destination

          0 format errors, 0 checksum errors, 0 bad hop count

          0 unknown protocol, 0 not a gateway

          0 security failures, 0 bad options

    Frags: 0 reassembled, 0 timeouts, 0 too big

          0 fragmented, 0 couldn't fragment

   Bcast: 38 received, 52 sent

   Sent: 44 generated, 0 forwarded

          0 encapsulation failed, 0 no route

 ICMP statistics:

   Rcvd:  0 format errors, 0 checksum errors, 0 redirects, 0 unreachable

          0 echo, 0 echo reply, 0 mask requests, 0 mask replies, 0 quench

          0 parameter, 0 timestamp, 0 info request, 0 other

   Sent:  0 redirects, 3 unreachable, 0 echo, 0 echo reply

          0 mask requests, 0 mask replies, 0 quench, 0 timestamp

          0 info reply, 0 time exceeded, 0 parameter problem

 UDP statistics:

   Rcvd:  56 total, 0 checksum errors, 55 no port

   Sent:  18 total, 0 forwarded broadcasts

 TCP statistics:

   Rcvd:  0 total, 0 checksum errors, 0 no port

   Sent:  0 total

 EGP statistics:

   Rcvd:  0 total, 0 format errors, 0 checksum errors, 0 no listener

   Sent:  0 total

 IGRP statistics:

   Rcvd:  73 total, 0 checksum errors

   Sent:  26 total

 HELLO statistics:

   Rcvd:  0 total, 0 checksum errors

   Sent:  0 total

 ARP statistics:

   Rcvd:  20 requests, 17 replies, 0 reverse, 0 other

   Sent:  0 requests, 9 replies (0 proxy), 0 reverse

 Probe statistics:

   Rcvd:  6 address requests, 0 address replies

 0 proxy name requests, 0 other

   Sent:  0 address requests, 4 address replies (0 proxy)

          0 proxy name replies

Table 15 describes significant fields shown in the display.

Table 15 show ip traffic Field Descriptions
Field	Description
format errors	A gross error in the packet format, such as an impossible Internet header length.
bad hop count	Occurs when a packet is discarded because its time-to-live (TTL) field was decremented to zero.
encapsulation failed	Usually indicates that the router had no ARP request entry and therefore did not send a datagram.
no route	Counted when the Cisco IOS software discards a datagram it did not know how to route.
proxy name reply	Counted when the Cisco IOS software sends an ARP or Probe Reply on behalf of another host. The display shows the number of probe proxy requests that have been received and the number of responses that have been sent.

show standby

To display Hot Standby Router Protocol (HSRP) information, use the show standby EXEC command.

show standby [type number [group]] [brief]

Syntax Description


type number	(Optional) Interface type and number for which output is displayed.
group	(Optional) Group number on the interface for which output is displayed.
brief	(Optional) A single line of output summarizes each standby group.

Command Modes

EXEC

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

If you want to specify a group, you must also specify an interface type and number.

Examples

The following is sample output from the show standby command:

Router# show standby

Ethernet0 - Group 0

  Local state is Active, priority 100, may preempt

  Hellotime 3 holdtime 10

  Next hello sent in 0:00:00

  Hot standby IP address is 198.92.72.29 configured

  Active router is local

  Standby router is 198.92.72.21 expires in 0:00:07

  Tracking interface states for 2 interfaces, 2 up:

    Up    Ethernet0

    Up    Serial0

The following is sample output from the show standby command with a specific interface and the brief keyword:

Router# show standby ethernet0 brief

Interface   Grp Prio P State    Active addr     Standby addr    Group addr

Et0         0   100    Standby  171.69.232.33   local           172.19.48.254

Table 16 describes the fields in the display.

Table 16 show standby Field Descriptions
Field	Description
Ethernet0 – Group 0	Interface type and number and Hot Standby group number for the interface.
Local state is …	State of local router; can be one of the following: •Active—Current Hot Standby router •Standby—Router next in line to be the Hot Standby router
priority	Priority value of the router based on the standby priority, standby preempt command.
may preempt (indicated by P in thebriefoutput)	Indicates that the router will attempt to assume control as the active router if its priority is greater than the current active router.
Hellotime	Time between hello packets (in seconds), based on the standby timers command.
holdtime	Time (in seconds) before other routers declare the active or standby router to be down, based on the standby timers command.
Next hello sent in …	Time in which the Cisco IOS software will send the next hello packet (in hours:minutes:seconds).
Hot Standby IP address is … configured	IP address of the current Hot Standby router. The word “configured” indicates that this address is known through the standby ip command. Otherwise, the address was learned dynamically through HSRP hello packets from other routers that do have the HSRP IP address configured.
Active router is …	Value can be “local” or an IP address. Address of the current active Hot Standby router.
Standby router is …	Value can be “local” or an IP address. Address of the “standby” router (the router that is next in line to be the Hot Standby router).
expires in	Time (in hours:minutes:seconds) in which the standby router will no longer be the standby router if the local router receives no hello packets from it.
Tracking interface states for …	List of interfaces that are being tracked and their corresponding states. Based on thestandby track command.

Related Commands


Command	Description
standby authentication	Configures an authentication string for the HSRP.
standby ip	Activates the HSRP.
standby priority, standby preempt	Configures HSRP priority, preemption, and preemption delay.
standby timers	Configures the time between hellos and the time before other routers declare the active Hot Standby or standby router to be down.
standby track	Configures an interface so that the Hot Standby priority changes based on the availability of other interfaces.
standby use-bia	Configures HSRP to use the burned-in address of the interface as its virtual MAC address, instead of the preassigned MAC address (on Ethernet and FDDI) or the functional address (on Token Ring).

show tcp statistics

To display TCP statistics, use the show tcp statistics EXEC command.

show tcp statistics

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History

Release	Modification
11.3	This command was introduced.

Examples

The following is sample output from the show tcp statistics command:

Router# show tcp statistics

Rcvd: 210 Total, 0 no port

      0 checksum error, 0 bad offset, 0 too short

      132 packets (26640 bytes) in sequence

      5 dup packets (502 bytes)

      0 partially dup packets (0 bytes)

      0 out-of-order packets (0 bytes)

      0 packets (0 bytes) with data after window

      0 packets after close

      0 window probe packets, 0 window update packets

      0 dup ack packets, 0 ack packets with unsend data

      69 ack packets (3044 bytes)

Sent: 175 Total, 0 urgent packets

      16 control packets (including 1 retransmitted)

      69 data packets (3029 bytes)

      0 data packets (0 bytes) retransmitted

      73 ack only packets (49 delayed)

      0 window probe packets, 17 window update packets

7 Connections initiated, 1 connections accepted, 8 connections established

8 Connections closed (including 0 dropped, 0 embryonic dropped)

1 Total rxmt timeout, 0 connections dropped in rxmt timeout

0 Keepalive timeout, 0 keepalive probe, 0 Connections dropped in keepalive

Table 17 describes significant fields shown in the display.

Table 17 show tcp statistics Field Descriptions
Field	Description
Rcvd:	Statistics in this section refer to packets received by the router.
Total	Total packets received.
no port	Number of packets received with no port.
checksum error	Number of packets received with checksum error.
bad offset	Number of packets received with bad offset to data.
too short	Number of packets received that were too short.
packets in sequence	Number of data packets received in sequence.
dup packets	Number of duplicate packets received.
partially dup packets	Number of packets received with partially duplicated data.
out-of-order packets	Number of packets received out of order.
packets with data after window	Number of packets received with data that exceeded the receiver’s window size.
packets after close	Number of packets received after the connection has been closed.
window probe packets	Number of window probe packets received.
window update packets	Number of window update packets received.
dup ack packets	Number of duplicate acknowledgment packets received.
ack packets with unsent data	Number of acknowledgment packets with unsent data received.
ack packets	Number of acknowledgment packets received.
Sent:	Statistics in this section refer to packets sent by the router.
Total	Total number of packets sent.
urgent packets	Number of urgent packets sent.
control packets	Number of control packets (SYN, FIN, or RST) sent.
data packets	Number of data packets sent.
data packets retransmitted	Number of data packets retransmitted.
ack only packets	Number of packets sent that are acknowledgments only.
window probe packets	Number of window probe packets sent.
window update packets	Number of window update packets sent.
Connections initiated	Number of connections initiated.
connections accepted	Number of connections accepted.
connections established	Number of connections established.
Connections closed	Number of connections closed.
Total rxmt timeout	Number of times the router tried to retransmit, but timed out.
Connections dropped in rxmit timeout	Number of connections dropped in retransmit timeout.
Keepalive timeout	Number of keepalive packets in timeout.
keepalive probe	Number of keepalive probes.
Connections dropped in keepalive	Number of connections dropped in keepalive.

Related Commands

Command	Description
clear tcp statistics	Clears TCP statistics.

standby authentication

To configure an authentication string for the Hot Standby Router Protocol (HSRP), use the standby authentication interface configuration command. To delete an authentication string, use the no form of this command.

standby [group-number] authentication string

no standby [group-number] authentication string

Syntax Description

group-number	(Optional) Group number on the interface to which this authentication string applies.
string	Authentication string. It can be up to eight characters in length. The default string iscisco.

Defaults

group-number: 0
string: cisco

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

The authentication string is transmitted unencrypted in all HSRP messages. The same authentication string must be configured on all routers and access servers on a cable to ensure interoperation. Authentication mismatch prevents a device from learning the designated Hot Standby IP address and the Hot Standby timer values from other routers configured with HSRP. Authentication mismatch does not prevent protocol events such as one router taking over as the designated router.

When group number 0 is used, no group number is written to NVRAM, providing backward compatibility.

Examples

The following example configures “word” as the authentication string required to allow Hot Standby routers in group 1 to interoperate:

interface ethernet 0

 standby 1 authentication word

standby ip

To activate the Hot Standby Router Protocol (HSRP), use the standby ip interface configuration command. To disable HSRP, use the no form of this command.

standby [group-number] ip [ip-address [secondary]]

no standby [group-number] ip [ip-address]

Syntax Description


group-number	(Optional) Group number on the interface for which HSRP is being activated. Default is 0.
ip-address	(Optional) IP address of the Hot Standby Router interface.
secondary	(Optional) Indicates the IP address is a secondary Hot Standby Router interface. Useful on interfaces with primary and secondary addresses; you can configure primary and secondary HSRP addresses.

Defaults

group-number: 0

HSRP is disabled.

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.
10.3	The group-numer argument was added.
11.1	The secondary keyword was added.

Usage Guidelines

The standby ip command activates HSRP on the configured interface. If an IP address is specified, that address is used as the designated address for the Hot Standby group. If no IP address is specified, the designated address is learned through the standby function. For HSRP to elect a designated router, at least one router on the cable must have been configured with, or learned, the designated address. Configuring the designated address on the active router always overrides a designated address that is currently in use.

When the standby ip command is enabled on an interface, the handling of proxy ARP requests is changed (unless proxy ARP was disabled). If the interface’s Hot Standby state is active, proxy ARP requests are answered using the Hot Standby group’s MAC address. If the interface is in a different state, proxy ARP responses are suppressed.

When group number 0 is used, no group number is written to NVRAM, providing backward compatibility.

Examples

The following example activates HSRP for group 1 on Ethernet interface 0. The IP address used by the Hot Standby group will be learned using HSRP.

interface ethernet 0

 standby 1 ip

In the following example, all three virtual IP addresses appear in the ARP table using the same (single) virtual MAC address. All three virtual IP addresses are using the same HSRP group (group 0).

ip address 1.1.1.1. 255.255.255.0

ip address 1.2.2.2. 255.255.255.0 secondary

ip address 1.3.3.3. 255.255.255.0 secondary

ip address 1.4.4.4. 255.255.255.0 secondary

standby ip 1.1.1.254

standby ip 1.2.2.254 secondary

standby ip 1.3.3.254 secondary

standby mac-address

To specify a virtual MAC address for Hot Standby Router Protocol (HSRP), use the standby mac-address interface configuration command. To revert to the standard virtual MAC address (0000.0C07.ACxy), use the no form of this command.

standby [group-number] mac-address macaddress

no standby [group-number] mac-address

Syntax Description


group-number	(Optional) Group number on the interface for which HSRP is being activated. The default is 0.
macaddress	Media Access Control (MAC) address.

Defaults

If this command is not configured, and the standby use-bia command is not configured, the standard virtual MAC address is used: 0000.0C07.ACxy, where xy is the group number in hexadecimal. This address is specified in RFC 2281, Cisco Hot Standby Router Protocol (HSRP).

Command Modes

Interface configuration

Command History


Release	Modification
11.2	This command was introduced.

Usage Guidelines

This command can not be used on a Token Ring Interface.

HSRP is used to help endstations locate the first hop gateway for IP routing. The endstations are configured with a default gateway. However, HSRP can provide first-hop redundancy for other protocols. Some protocols, such as APPN, use the MAC address to identify the first hop for routing purposes. In this case, it is often necessary to be able to specify the virtual MAC address; the virtual IP address is unimportant for these protocols. Use the standby mac-address command to specify the virtual MAC address.

The MAC address specified is used as the virtual MAC address when the router is active.

This command is intended for certain APPN configurations. The parallel terms are as follows:

APPN IP
end node host
network node router or gateway

In an APPN network, an end node is typically configured with the MAC address of the adjacent network node. Use the standby mac-address command in the routers to set the virtual MAC address to the value used in the end nodes.

Examples

If the end nodes are configured to use 4000.1000.1060 as the MAC address of the network node, the command to configure HSRP group 1 with the virtual MAC address is as follows:

 standby 1 mac-address 4000.1000.1060

Related Commands


Command	Description
show standby	Displays HSRP information.
standby use-bia	Configures HSRP to use the burned-in address of the interface as its virtual MAC address.

standby mac-refresh

To change the interval at which packets are sent to refresh the MAC cache when Hot Standby Router Protocol (HSRP) is running over FDDI, use the standby mac-refresh interface configuration command. To restore the default value, use the no form of this command.

standby mac-refresh seconds

no standby mac-refresh

Syntax Description


seconds	Number of seconds in the interval at which a packet is sent to refresh the MAC cache. The maximum value is 255 seconds. The default is 10 seconds.

Defaults

10 seconds

Command Modes

Interface configuration

Command History


Release	Modification
12.0	This command was introduced.

Usage Guidelines

This command applies to HSRP running over FDDI only. Packets are sent every 10 seconds to refresh the MAC cache on learning bridges or switches. By default, the MAC cache entries age out in 300 seconds (5 minutes).

All other routers participating in HSRP on the FDDI ring receive the refresh packets, although the packets are intended only for the learning bridge or switch. Use this command to change the interval. Set the interval to 0 if you want to prevent refresh packets (if you have FDDI but do not have a learning bridge or switch).

Examples

The following example changes the MAC refresh interval to 100 seconds. Therefore, a learning bridge would have to miss three packets before the entry ages out.

standby mac-refresh 100

standby priority, standby preempt

To configure Hot Standby Router Protocol (HSRP) priority, preemption, and preemption delay, use the standby interface configuration command. To restore the default values, use the no form of this command.

standby [group-number] priority priority [preempt [delay delay]]

standby [group-number] [priority priority] preempt [delay delay]

no standby [group-number] priority priority [preempt [delay delay]]

no standby [group-number] [priority priority] preempt [delay delay]

Syntax Description


group-number	(Optional) Group number on the interface to which the other arguments in this command apply.
prioritypriority	(Optional) Priority value that prioritizes a potential Hot Standby router. The range is 1 to 255, where 1 denotes the lowest priority and 255 denotes the highest priority. The default priority value is 100. The router in the HSRP group with the highest priority value becomes the active router.
preempt	(Optional) The router is configured to preempt, which means that when the local router has a Hot Standby priority higher than the current active router, the local router should attempt to assume control as the active router. If preempt is not configured, the local router assumes control as the active router only if it receives information indicating that there is no router currently in the active state (acting as the designated router).
delaydelay	(Optional) Time in seconds. The delay argument causes the local router to postpone taking over the active role for delay seconds since that router was last restarted. The range is 0 to 3600 seconds (1 hour). The default is 0 seconds (no delay).

Defaults

group-number: 0

priority: 100

delay: 0 seconds; if the router wants to preempt, it will do so immediately.

Command Modes

Interface configuration

Command History


Release	Modification
11.3	This command was introduced.

Usage Guidelines

When using this command, you must specify at least one keyword (priority or preempt), or you can specify both.

When group number 0 is used, no group number is written to NVRAM, providing backward compatibility.

The assigned priority is used to help select the active and standby routers. Assuming preemption is enabled, the router with the highest priority becomes the designated active router. In case of ties, the primary IP addresses are compared, and the higher IP address has priority.

Note that the device’s priority can change dynamically if an interface is configured with the standby track command and another interface on the router goes down.

When a router first comes up, it does not have a complete routing table. If it is configured to preempt, it will become the active router, yet it is unable to provide adequate routing services. This problem is solved by configuring a delay before the preempting router actually preempts the currently active router.

Examples

In the following example, the router has a priority of 120 (higher than the default value) and will wait for 300 seconds (5 minutes) before attempting to become the active router:

interface ethernet 0 
 standby ip 172.19.108.254

 standby priority 120 preempt delay 300

Related Commands


Command	Description
standby track	Configures an interface so that the Hot Standby priority changes based on the availability of other interfaces.

standby timers

To configure the time between hellos and the time before other routers declare the active Hot Standby or standby router to be down, use the standby timers interface configuration command. To restore the timers to their default values, use the no form of this command.

standby [group-number] timers [msec] hellotime [msec] holdtime

no standby [group-number] timers [msec] hellotime [msec] holdtime

Syntax Description


group-number	(Optional) Group number on the interface to which the timers apply. The default is 0.
msec	(Optional) Interval in milliseconds. Millisecond timers allow for faster failover.
hellotime	Hello interval in seconds.This is an integer from 1 to 255. The default is 3 seconds. If themsec option is specified, hello interval is in milliseconds. This is an integer from 20 to 999.
holdtime	Time in seconds before the active or standby router is declared to be down. This is an integer from 1 to 255. The default is 10 seconds. If the msec option is specified, holdtime is in milliseconds. This is an integer from 20 to 999.

Defaults

group-number: 0
hellotime: 3 seconds
holdtime: 10 seconds

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.
11.2	The msec keyword was added.

Usage Guidelines

The standby timers command configures the time between standby hellos and the time before other routers declare the active or standby router to be down. Routers or access servers on which timer values are not configured can learn timer values from the active or standby router. The timers configured on the active router always override any other timer settings. All routers in a Hot Standby group should use the same timer values. Normally, holdtime is greater than or equal to 3 times the value of hellotime, (holdtime > 3 *hellotime).

The value of the standby timer will not be learned through HSRP hellos if it is less than 1 second.

When group number 0 is used, no group number is written to NVRAM, providing backward compatibility.

Examples

The following example sets, for group number 1 on Ethernet interface 0, the time between hello packets to 5 seconds, and the time after which a router is considered to be down to 15 seconds:

interface ethernet 0

 standby 1 ip

 standby 1 timers 5 15

The following example sets, for the Hot Router interface located at 172.19.10.1 on Ethernet interface 0, the time between hello packets to 300 milliseconds, and the time after which a router is considered to be down to 900 milliseconds.

interface ethernet 0

 standby ip 172.19.10.1

 standby timers msec 300 msec 900

standby track

To configure an interface so that the Hot Standby priority changes based on the availability of other interfaces, use the standby track interface configuration command. To remove the tracking, use the no form of this command.

standby [group-number] track type number [interface-priority]

no standby [group-number] track type number [interface-priority]

Syntax Description


group-number	(Optional) Group number on the interface to which the tracking applies.
type	Interface type (combined with interface number) that will be tracked.
number	Interface number (combined with interface type) that will be tracked.
interface-priority	(Optional) Amount by which the Hot Standby priority for the router is decremented (or incremented) when the interface goes down (or comes back up). The default value is 10.

Defaults

group-number: 0

interface-priority: 10

Command Modes

Interface configuration

Command History


Release	Modification
10.3	This command was introduced.

Usage Guidelines

This command ties the router’s Hot Standby priority to the availability of its interfaces. It is useful for tracking interfaces that are not configured for the Hot Standby Router Protocol.

When a tracked interface goes down, the Hot Standby priority decreases by 10. If an interface is not tracked, its state changes do not affect the Hot Standby priority. For each interface configured for Hot Standby, you can configure a separate list of interfaces to be tracked.

The optional argument interface-priority specifies how much to decrement the Hot Standby priority by when a tracked interface goes down. When the tracked interface comes back up, the priority is incremented by the same amount.

When multiple tracked interfaces are down and interface-priority values have been configured, these configured priority decrements are cumulative. If tracked interfaces are down, but none of them were configured with priority decrements, the default decrement is 10 and it is noncumulative.

When group number 0 is used, no group number is written to NVRAM, providing backward compatibility.

Examples

In the following example, Ethernet interface 1 tracks Ethernet interface 0 and serial interface 0. If one or both of these two interfaces go down, the Hot Standby priority of the router decreases by 10. Because the default Hot Standby priority is 100, the priority becomes 90 when one or both of the tracked interfaces go down.

interface ethernet 1

 ip address 198.92.72.37 255.255.255.240

 no ip redirects

 standby track ethernet 0

 standby track serial 0

 standby preempt

 standby ip 198.92.72.46

Related Commands


Command	Description
standby priority, standby preempt	Configures HSRP priority, preemption, and preemption delay.

standby use-bia

To configure Hot Standby Router Protocol (HSRP) to use the interface’s burned-in address as its virtual MAC address, instead of the preassigned MAC address (on Ethernet and FDDI) or the functional address (on Token Ring), use the standby use-bia interface configuration command. To restore the default virtual MAC address, use the no form of this command.

standby use-bia

no standby use-bia

Syntax Description

This command has no arguments or keywords.

Defaults

HSRP uses the preassigned MAC address on Ethernet and FDDI, or the functional address on Token Ring.

Command Modes

Interface configuration

Command History


Release	Modification
11.2	This command was introduced.

Usage Guidelines

For an interface with this command configured, only one standby group can be configured. Multiple groups need to be removed before this command is configured. Hosts on the interface need to have a default gateway configured. It is recommended you set theno ip proxy-arp command on the interface. It is desirable to configure the standby use-bia command on a Token Ring interface if there are devices that reject ARP replies with source hardware addresses set to a functional address.

When HSRP runs on a multiple-ring, source-routed bridging environment and the HRSP routers reside on different rings, configuring the standby use-bia command can prevent RIF confusion.

Examples

In the following example, the burned-in address of Token Ring interface 4/0 will be the virtual MAC address mapped to the virtual IP address:

interface token4/0

 standby use-bia

transmit-interface

To assign a transmit interface to a receive-only interface, use the transmit-interface interface configuration command. To return to normal duplex Ethernet interfaces, use the no form of this command.

transmit-interface type number

no transmit-interface

Syntax Description


type	Transmit interface type to be linked with the (current) receive-only interface.
number	Transmit interface number to be linked with the (current) receive-only interface.

Defaults

Disabled

Command Modes

Interface configuration

Command History


Release	Modification
10.0	This command was introduced.

Usage Guidelines

Receive-only interfaces are used commonly with microwave Ethernet links.

Examples

The following example specifies Ethernet interface 0 as a simplex Ethernet interface:

interface ethernet 1

 ip address 128.9.1.2

 transmit-interface ethernet 0

GlobalBusinessArticles.biz

Build your business with sponsored ads

GlobalBusinessArticles.biz

Build your business with sponsored ads

BONK, POPCAT and Solana memecoins stay green even as Bitcoin price drops

Stripe bringing back crypto payments, this time with a stablecoin

Will Dogecoin skyrocket 7 months after the Bitcoin halving again?

Square merchants can now convert up to 10% of sales to Bitcoin via Cash App

Bitcoin’s funding rate flattens, but should BTC bulls rejoice and buy the dips?

Boomers to pour $300B into crypto markets — Morgan Creek Capital

Here’s what happened in crypto today

Consensys files lawsuit against SEC and commissioners over Ether regulation

Blockaid says it caused crypto drainer to shut down, defends against claims of &#039;false positives&#039;

‘Persistent inflation’ will be key in Bitcoin’s run to $200K — Crypto fund manager

access-class

Syntax Description

Defaults

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

access-list (IP extended)

Syntax Description

Defaults

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

access-list (IP standard)

Syntax Description

Defaults

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

clear access-list counters

Syntax Description

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

clear ip accounting

Syntax Description

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

clear ip drp

Syntax Description

Command Modes

Command History

Examples

Related Commands

clear tcp statistics

Syntax Description

Command Modes

Command History

Examples

Related Commands

deny (IP)

Syntax Description

Defaults

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

dynamic

Syntax Description

Defaults

Command Modes

Command History

Usage Guidelines

Examples

Related Commands

Blockaid says it caused crypto drainer to shut down, defends against claims of 'false positives'